Last Updated on August 10, 2022 by Kimberly Crawford
Do you have a Frigidaire refrigerator that isn’t cooling? This can be a huge problem, especially if you need to store food in your fridge.
In this blog post, we will discuss six common reasons why your Frigidaire refrigerator may not be cooling and how to fix them.
We will also provide some tips on how to keep your fridge running efficiently so that it doesn’t break down in the future.
Reasons why Frigidaire refrigerator not cooling.
There are a few reasons that your Frigidaire refrigerator may not be cooling properly. Check the following to see if any of these could be the issue:
1. Broken Compressor.
If your Frigidaire refrigerator is not cooling, it may be due to a broken compressor. The compressor is responsible for circulating coolant throughout the fridge, so if it’s not working properly, the fridge will not be able to maintain a cool temperature. There are a few ways to tell if your fridge’s compressor is broken:
-The fridge will make a loud noise when it’s turned on
-The fridge will take longer than usual to cool down
-There may be ice buildup inside the fridge
Why does it fail?
The compressor is the heart of the refrigerator, pumping refrigerant through the system. If it fails, the fridge won’t cool. Compressors fail for a number of reasons.
The most common is simply age—after years of use, they just wear out. But if your fridge is relatively new and the compressor fails, it could be because of a manufacturing defect, overloading, or poor maintenance.
If your fridge is starting to make strange noises, it’s probably time to call a repairman. A new compressor can cost $200 or more, so it’s often cheaper to just buy a new fridge. But if your fridge is otherwise in good condition, it’s worth fixing.
How to fix it?
If the compressor is the problem, you’ll need to replace it. This is a job for a qualified refrigerator technician. They will be able to properly diagnose the problem and make the necessary repairs. Replacing a compressor can be expensive, so be sure to get a few estimates before you make a decision.
2. Broken Start Relay.
If your Frigidaire refrigerator is not cooling, it may be because the start relay is broken. The start relay is a small black box that is located on the back of the fridge, near the compressor.
If this part is broken, it will prevent the compressor from running, and your fridge will not be able to cool down.
Why does it fail?
There are a few reasons that the start relay might fail.
The most common one is age and wear and tear.
Another reason could be due to voltage issues, meaning that the fridge isn’t getting enough power to run properly.
Lastly, it could be because of a problem with the compressor itself. If you’re having trouble with your fridge not cooling, it’s best to check the start relay first.
How do you fix it?
Luckily, the start relay is a relatively easy fix. You can either replace it with a new one or try and repair it. If you’re going to replace it, you’ll need to get the correct model for your fridge.
You can find this information in the owner’s manual. If you’re going to try and repair it, you’ll need to open up the fridge and check the connections. Make sure that they’re all tight and secure.
To replace the start relay, you will need to purchase a new one from a Frigidaire dealer or an appliance parts store.
Be sure to get the correct model number for your fridge, as there are many different types of start relays. Once you have the new part, simply remove the old one and install the new one in its place.
If you’re going to try and repair the start relay, you’ll need a few tools. First, you’ll need a screwdriver. Next, you’ll need a multimeter to test the continuity of the coils. Lastly, you’ll need some soldering equipment if any of the connections are loose or broken.
The start relay is a vital part of your fridge, so it’s important to keep an eye on it. If it starts to fail, don’t hesitate to either replace or repair it.
3. Broken Start Relay Capacitor.
If your Frigidaire refrigerator is not cooling, it may be due to a broken start relay capacitor. This part helps to start the compressor and keeps it running.
If it is damaged, it will need to be replaced. You can find this part at most hardware stores or online retailers. Be sure to unplug your fridge before beginning any repairs.
Why does it fail?
There are two reasons why the start relay capacitor fails. The first is because of a manufacturing defect. The second reason is because the refrigerator is not properly maintained. Both of these problems can be fixed by replacing the start relay capacitor.
How do you know if your start relay capacitor is failing?
The most common symptom of a failing start relay capacitor is a clicking noise coming from the refrigerator. This noise is caused by the electrical contacts inside the start relay capacitor failing to make a proper connection.
If you hear this clicking noise, it’s important to unplug the refrigerator and call a qualified repair technician. Attempting to repair the problem yourself could result in further damage to the refrigerator.
What does it cost to replace the start relay capacitor?
Replacing the start relay capacitor is a relatively simple repair that can be completed in about 30 minutes. The average cost for this repair is between $100 and $150, depending on the make and model of your refrigerator.
If your Frigidaire refrigerator is not cooling properly, it may be due to a failing start relay capacitor. This problem can be fixed by replacing the capacitor. The average cost for this repair is between $100 and $150.
Call a qualified repair technician if you hear a clicking noise coming from your refrigerator. Do not attempt to repair the problem yourself as this could result in further damage.
How to fix it.
If your Frigidaire refrigerator is not cooling, it may be due to a broken start relay capacitor. This is a relatively easy fix that you can do yourself.
First, locate the start relay capacitor on the back of the fridge. It will look like a small black box with two wires coming out of it.
Next, use a multimeter to test the capacitor for continuity. If there is no continuity, then the capacitor needs to be replaced.
To do this, simply disconnect the two wires from the old capacitor and connect them to the new one. Then, reattach the black box to the back of the fridge.
Once you have done this, your fridge should be back to cooling normally. If it is still not cooling properly, then you may need to call a repairman.
If you have any questions about this repair, be sure to ask a professional. Attempting to fix your fridge on your own could void the warranty and cause further damage. With some simple tools and a little know-how, however, this is a repair that most people can do themselves.
4. Broken Temperature Thermostat.
Why does it fail?
The internal temperature of the fridge is too high.
What are the symptoms?
The refrigerator will not cool down no matter how low you set the thermostat. The compressor may run constantly or sporadically. You may hear clicking noises coming from the back of the fridge.
How to fix it?
The first thing you’ll want to do is make sure that the power is turned off to your refrigerator. Next, locate the thermostat on the back of your fridge. It will be a small round knob. Once you’ve found it, turn it to the left as far as it will go.
If this doesn’t fix the problem, then the next step is to replace the thermostat. This is a relatively easy repair that you can do yourself. Simply unscrew the old thermostat and screw in the new one. Be sure to turn off the power to your fridge before you begin this repair.
If your refrigerator still isn’t cooling after these two steps, then you may need to call a repairman. It’s possible that there is a more serious problem with your fridge, such as a Freon leak.
5. Broken Thermistor (Temperature Sensor).
If your Frigidaire refrigerator is not cooling, one possible reason is a broken thermistor. The thermistor is a temperature sensor located in the fridge that helps regulate the internal temperature. If it’s broken, it can cause the fridge to either get too cold or not cold enough.
Why does it fail?
There are a few reasons that your Thermistor may have failed. One reason is that it may be old and simply needs to be replaced.
Another reason could be that there is something blocking the sensor, such as dust or dirt. Finally, it is also possible that the fridge itself is not properly ventilated, which can cause the sensor to fail.
To test whether the thermistor is working, you’ll need to use a multimeter to check the resistance. If the resistance is infinite, that means the thermistor is open and needs to be replaced. If the resistance is zero, that means the thermistor is shorted and also needs to be replaced.
If your fridge is still not cooling after replacing the thermistor, there may be another issue at play. It’s best to consult a refrigerator repair professional to diagnose and fix the problem.
How to fix it?
If your Thermistor has failed, there are a few things you can do to fix it. First, try cleaning the sensor with a soft cloth and some warm water.
If this does not work, you may need to replace the sensor entirely. You can purchase a new one from most appliance stores or online retailers. Finally, make sure that your fridge is properly ventilated to prevent the sensor from failing again in the future.
6. Dirty Condenser Coils.
One of the most common reasons a refrigerator stops cooling is because the condenser coils are dirty. These coils are responsible for removing heat from the refrigerant, so if they’re covered in dirt and dust, they can’t do their job properly.
Why does it fail?
Your Frigidaire refrigerator has a condenser coil that helps to cool the fridge. This coil can get dirty over time, and when it does, it won’t be able to do its job properly.
How to fix it?
If your fridge isn’t cooling, one of the first things you should check is the condenser coils.
If they’re dirty, you can clean them yourself with a brush and some soapy water. Just be sure to unplug your fridge first! Once you’ve cleaned the coils, your fridge should start cooling properly again.
If your fridge is still not cooling after you’ve cleaned the condenser coils, there may be another issue at play. Check the fridge’s thermostat to see if it’s set to the correct temperature. If it is, then you may need to call a repair person to take a look at your fridge.
7. Faulty Condenser Fan Motor.
If your Frigidaire refrigerator is not cooling, it may be because the condenser fan motor is not working properly. This can be caused by a number of things, such as a blown fuse or a tripped circuit breaker.
If you have checked these things and the condenser fan motor still does not work, it may need to be replaced.
Why does it fail?
There are a few reasons why your condenser fan motor might fail. The most common reason is that the bearings in the motor have failed. When this happens, the motor will make a loud noise and eventually seize up.
Another reason for failure is that the windings in the motor have burned out. This can happen if the fridge is overloaded and the motor has to work too hard. Finally, the motor can simply wear out over time and stop working.
How to fix it?
The most likely problem is that the condenser fan motor has failed. This is a common issue with Frigidaire refrigerators. The good news is that it is a pretty easy fix. You just need to replace the condenser fan motor.
Here are the steps:
First, you need to locate the condenser fan motor. It is usually located in the back of the refrigerator, near the compressor.
Next, you need to remove the old condenser fan motor. This is usually just a matter of unscrewing a few screws.
Then, you need to install the new condenser fan motor. Again, this is just a matter of screwing in a few screws.
Finally, you need to test the refrigerator to make sure that it is cooling properly.
If you need to replace the condenser fan motor, you can find one at most appliance parts stores. Be sure to take the old one with you so that you can get the correct replacement. Installation is usually pretty straightforward, but if you have any questions, be sure to ask a staff member at the store for help.
8. Faulty Control Board.
If your Frigidaire refrigerator is not cooling, it may be due to a faulty control board. The control board controls the compressor and fans, and if it is malfunctioning, the fridge will not cool properly.
To test the control board, check for continuity between the two terminals on the board using a multimeter. If there is no continuity, the board needs to be replaced.
Why does it fail?
There are a few reasons why your Frigidaire refrigerator’s control board might fail. The most common reason is due to a power surge. This can cause the control board to fry and stop working. Other reasons include, but are not limited to, corrosion, water damage, or physical damage.
If you suspect that your control board is failing, you should contact a qualified refrigerator repair technician to diagnose and replace the part. Trying to fix it yourself could void your warranty, and potentially cause more damage.
How to fix it?
Frigidaire refrigerator not cooling? This may be due to a faulty control board. Luckily, this is an easy fix. Simply replace the control board with a new one and your fridge should be back to normal in no time!
9. Faulty Evaporator Fan Motor.
If your Frigidaire refrigerator is not cooling, one possible cause is a faulty evaporator fan motor. This part circulates air over the evaporator coils to keep them cool. If it’s not working properly, the coils will get too warm and cause the fridge to stop cooling.
To test whether the evaporator fan motor is the issue, open up your fridge and locate the coils. If they’re covered in frost or ice, that’s a good sign that the fan isn’t working properly.
Why does it fail?
There are a few reasons that your evaporator fan motor might fail. One of the most common is because of a build-up of ice on the coils. When this happens, it prevents air from flowing properly and causes the motor to overheat and eventually fail.
Another reason for failure is simply age and wear and tear. Over time, the motor can wear out and eventually fail.
How to fix it?
If your evaporator fan motor has failed, there are a few things you can do to fix it. One is to simply replace the motor. This is usually the most effective solution and will get your fridge back up and running in no time.
Another option is to clean the coils and make sure there is no ice build-up. This can be done with a simple coil cleaning kit. Finally, if the motor is simply old and worn out, you may need to replace it with a new one.
If you suspect that the evaporator fan motor is to blame for your fridge not cooling, it’s best to call a professional for help. Trying to fix it yourself could void your warranty.
10. Refrigerator Door Not Sealing Properly.
If your refrigerator door is not sealing properly, it can cause the inside of your fridge to become too warm. This can cause your food to spoil and make your ice cream melt. To fix this problem, you will need to adjust the door so that it seals properly.
If your refrigerator door is not sealing properly, it can be very frustrating. You may find that your food spoils more quickly, or that your ice cream melts. This can be a very annoying problem, but fortunately, it is one that you can fix yourself.
To fix a refrigerator door that is not sealing properly, you will need to adjust the door. This can be done by hand, and you will just need to make sure that the door is adjusted so that it seals properly. Once you have done this, your problem should be solved and you will not have to worry about your food spoiling or your ice cream melting.
If you find that adjusting the door does not solve the problem, then you may need to replace the gasket. The gasket is the rubber seal that goes around the edge of the door, and it can sometimes become damaged. If this is the case, then you will need to replace the gasket in order to fix the problem.
11. Refrigerator is overloaded.
Check to see if there is frost on the back wall of the freezer. If so, remove food from the freezer and discard any spoiled items. Next, check to see if the coils behind the refrigerator are dusty.
If they are, vacuum them off with a dustbuster or similar device. Finally, make sure that nothing is blocking the vents on either the fridge or freezer. If the vents are blocked, air cannot circulate properly and your fridge will not cool correctly.
Related:
- 10 Reasons For Whirlpool Refrigerator Not Cooling and {How To Fix}
- 8 Reasons for GE Refrigerator Not Cooling and {How To Fix}
Why Frigidaire refrigerator not cooling after moving?
If you’ve recently moved your Frigidaire refrigerator and it’s not cooling properly, there are a few things you can check. First, make sure that the power cord is plugged in correctly and that the fridge is receiving power. Next, check to see if the evaporator coils are frozen over. If they are, simply defrost them and see if that solves the problem.
If your Frigidaire refrigerator is still not cooling after moving, it’s possible that there’s an issue with the compressor. If this is the case, you’ll need to contact a professional for repair or replacement. However, most fridge compressors are covered by a five-year warranty, so you may be able to get it repaired or replaced for free.
Why is my Frigidaire fridge not cooling but freezer works?
If your Frigidaire fridge is not cooling but the freezer works, it could be due to a clogged air filter, dirty condenser coils, or a faulty evaporator fan motor. A clogged air filter can restrict airflow and cause the fridge to not cool properly.
Dirty condenser coils can also reduce airflow and cause the fridge to not cool properly. A faulty evaporator fan motor can also cause the fridge to not cool properly.
If you have checked all of these things and the fridge is still not cooling, you may need to call a repairman.
How do I run a diagnostic on my Frigidaire refrigerator?
There are a few things you need to do in order to run a diagnostic on your Frigidaire refrigerator. First, you will need to locate the control panel. Second, you will need to press and hold the “Fresh Food” and “Freezer” buttons at the same time for three seconds. After that, the display should show the diagnostic mode.
If it does not, you will need to press the “Fresh Food” and “Freezer” buttons again. Once the display shows the diagnostic mode, you can release the buttons. To exit the diagnostic mode, you will need to press and hold the “Fresh Food” and “Freezer” buttons at the same time for three seconds.
Where is the reset button on my Frigidaire freezer?
There are a few possible places the reset button might be located on your Frigidaire freezer. Check the back panel, near the bottom. There may also be a reset button inside the freezer, near the temperature control knob. If you can’t find the reset button, consult your owner’s manual for more information.
If your freezer isn’t working properly, resetting it may help. To do this, locate the reset button and press it for a few seconds. If the problem persists, you may need to call a technician for further assistance.
Where is the thermostat located on a Frigidaire refrigerator?
The thermostat is located on the back wall of the refrigerator, near the bottom. You will need to remove the panel on the back of the fridge to access it. The thermostat controls the temperature inside the fridge, so if your fridge is too cold or too warm, you may need to adjust it.
Conclusion
If your Frigidaire refrigerator is not cooling, don’t panic. There are a few things you can check and do to troubleshoot the problem. In most cases, you’ll be able to fix the issue yourself without having to call a repairman. So save yourself some money and follow these steps. Good luck!