Last Updated on August 20, 2022 by Kimberly Crawford
If your Kenmore refrigerator ice maker is not working, don’t worry – you’re not alone. This is a common problem that many people experience. In this blog post, we will discuss some of the most common reasons why the ice maker might not be working, as well as how to fix it. We will also provide some troubleshooting tips for those who are having difficulties resolving the issue on their own. Keep reading for more information!
Related: 17 Reasons for Kenmore Refrigerator Not Cooling and How to Fix It
Reasons Why Kenmore Refrigerator Ice Maker Not Working: How to Fix
1. Temperature Setting.
The first thing you should check is the temperature setting of your fridge. If it’s set too low, ice won’t form. Set the thermostat to a colder setting and wait 24 hours to see if ice forms.
2. Door Switch.
The door switch is located on the side of the fridge and controls whether the ice maker is turned on or not. If this switch is defective, it will need to be replaced.
To check if the door switch is working, open the freezer door and press down on the lever. If you hear a clicking noise, then the switch is working and is not the problem. If you don’t hear a noise, then the switch may be defective and will need to be replaced.
How does it fail?
The most common failure of the door switch is when it gets stuck in the closed position. This can be caused by dirt, grease, or other build-up on the switch itself or in its housing.
When this happens, the switch cannot properly sense whether the door is open or closed, and will not allow the ice maker to cycle on and off as it should.
In some cases, the switch can be cleaned and restored to working order. In other cases, it will need to be replaced.
How to fix it?
If the door switch is dirty or gummed up, you can try cleaning it with a cotton swab dipped in rubbing alcohol.
Be sure to clean both the switch itself and the area around it where it makes contact with the door. If this does not solve the problem, you will need to replace the door switch. You can find replacement switches at most hardware stores or online.
To replace the door switch, first locate the switch on the inside of the refrigerator. It is usually mounted near the top of the fridge, on either the left or right side.
Once you have located it, use a screwdriver to remove the two screws that hold it in place. Then, disconnect the wire harness from the switch and remove it completely.
3. Frozen Evaporator Coils.
One of the most common reasons your Kenmore refrigerator’s ice maker isn’t working is because the evaporator coils are frozen over.
When this happens, it prevents the coils from absorbing heat, which in turn prevents them from melting the ice in the ice maker.
How does it fail?
There are a few reasons why your evaporator coils might freeze over. One is if the freezer temperature is set too low.
Another is if there’s something blocking the coils, like food that’s been packed in too tightly. And finally, if there’s frost build-up on the coils, that can also cause them to freeze over.
How to fix it?
If your evaporator coils are frozen over, you’ll need to thaw them out before the ice maker will start working again.
The best way to do this is to unplug the fridge and leave the door open for a few hours. This will allow all the ice to melt and hopefully prevent the coils from freezing over again.
If you suspect that the reason your coils are freezing over is because the freezer temperature is too low, try adjusting it to a warmer setting.
And if there’s frost build-up on the coils, you can remove it with a hairdryer set to the “defrost” setting. Just be careful not to overdo it, as you don’t want to damage the coils.
4. Ice Level Control Board.
This is the board that tells the ice maker when to stop making ice. If this board fails, the ice maker will continue to make ice until it overflows.
How does it fail?
There is a sensing arm on this board that tells it when the ice bucket is full. Over time, the plastic gears on this arm wear out and strip.
When they strip, the ice maker doesn’t know when to stop making ice and will continue until it overflows.
The solution?
To test this board, you will need a multimeter. First, unplug the refrigerator and remove the back panel of the freezer compartment. Locate the ice level control board and test it for continuity. If the board is faulty, it will need to be replaced.
To replace the board, simply remove the old one and install the new one in its place. Be sure to unplug the refrigerator before beginning this repair.
5. Ice Maker Assembly.
The ice maker assembly is responsible for supplying water to the mold and freezing it into ice cubes. If your refrigerator’s ice maker isn’t working, the first thing you should check is the ice maker assembly. There are a few things that could cause the ice maker assembly to fail.
If the ice maker assembly is clogged, it will not be able to supply water to the mold. The ice maker assembly can become clogged with minerals from the water supply or food debris. To clean the ice maker assembly, remove it from the refrigerator and soak it in a solution of vinegar and water.
If the ice maker assembly is frozen, it will not be able to supply water to the mold. The ice maker assembly can become frozen if the freezer temperature is set too low. To thaw the ice maker assembly, remove it from the refrigerator and place it in a bowl of warm water.
If the ice maker assembly is damaged, it will not be able to supply water to the mold. The ice maker assembly can become damaged if it is dropped or if the refrigerator is jarred. If the ice maker assembly is damaged, it will need to be replaced.
6. Icemaker Mold Thermostat.
The icemaker mold thermostat is a small black switch located on the back of the ice maker. It senses the temperature of the ice mold (ice tray).
When it reaches the right temperature, usually between 15 and 20 degrees Fahrenheit, it trips and allows power to flow to the ice maker. This causes the ice maker to fill with water from the fill valve.
How does it fail?
Over time, the icemaker mold thermostat can become worn out or corroded. When this happens, it may not trip at the correct temperature, which can cause the ice maker to make too much or too little ice.
What are the symptoms?
If your ice maker is making too much or little ice, it is probably because the icemaker mold thermostat is not tripping at the correct temperature. This can cause the ice maker to overflow and make a mess in your freezer.
How to fix it?
If the icemaker mold thermostat is defective, the ice maker won’t make ice. To test the thermostat, use a multimeter to test it for continuity. If it doesn’t have continuity, replace it.
You can find the icemaker mold thermostat at most home improvement stores or online. Be sure to get one that is compatible with your model of refrigerator.
To replace the icemaker mold thermostat:
-Unplug the refrigerator.
-Remove the ice maker from the freezer (see your owner’s manual for instructions).
-Locate the icemaker mold thermostat on the back of the ice maker. It is a small black switch.
-Use a multimeter to test the thermostat for continuity. If it doesn’t have continuity, replace it.
-Reassemble the ice maker and plug in the refrigerator.
7. Icemaker Switch.
The icemaker switch is a switch that controls the ice maker in your refrigerator. It is usually located in the freezer section of your fridge. If your ice maker is not working, one possible reason is that the icemaker switch has been turned off.
How do I turn it on?
The switch controls power to the ice maker and should be in the “on” position for the ice maker to work. You can find the switch on the back of the refrigerator near the top. If it is in the “off” position, simply flip it to the “on” position and see if that fixes the problem.
8. Low Water Pressure.
One of the most common reasons a Kenmore refrigerator ice maker isn’t working is because of low water pressure.
If your home’s water pressure is too low, it can prevent the ice maker from getting the water it needs to make ice.
Fortunately, this is an easy problem to fix. You can usually increase your home’s water pressure by adjusting the pressure regulator on your water main.
If you’re not sure how to do this, you can contact a plumber or your local water utility company for help. Once the pressure regulator is adjusted, the ice maker should start working properly again.
9. Water Filter.
The water filter is located in the back, right-hand corner of your Kenmore refrigerator. It’s usually hidden behind a panel or grille, and it helps to remove impurities from your water before it goes into the ice maker.
If your ice maker isn’t working, one possible reason is that the water filter is clogged and needs to be replaced.
How do I know if my water filter needs to be replaced?
If your ice maker isn’t working and you suspect that the water filter might be the problem, you can check it yourself. First, locate the water filter (it should be in the back, right-hand corner of your fridge). Then, check to see if the indicator light is on.
If the indicator light is off, that means the water filter needs to be replaced. You can buy a replacement water filter at most home improvement stores or online.
To replace the water filter:
-Locate the water filter (it should be in the back, right-hand corner of your fridge).
-Remove the old water filter.
-Insert the new water filter.
-Reset the indicator light (if there is one).
10. Water Inlet Valve.
The water inlet valve is a valve that controls the flow of water into the refrigerator. It is located behind the lower grille at the bottom of the refrigerator.
What can go wrong?
The water inlet valve can become corroded and stop working properly. It can also freeze and burst, causing water damage to your refrigerator.
What are the symptoms?
If the water inlet valve is not working properly, your refrigerator will not be able to make ice. You may also notice water leaking from the bottom of your refrigerator.
How to fix it?
You can clean or replace the water inlet valve yourself. However, if you are not comfortable doing this, you can call a refrigerator repair technician to do it for you.
If your water inlet valve is frozen, you can thaw it out by using a hair dryer or placing a towel soaked in hot water on the valve. Once the ice has melted, you should be able to turn on the water and resume making ice.
If you have a water leak, you will need to replace the water inlet valve. To do this, you will need to shut off the water to your refrigerator and disconnect the water line from the valve.
Then, you can remove the old valve and install the new one. Once it is in place, you can reconnect the water line and turn on the water. Your refrigerator should now be able to make ice properly.
Related:
- LG Refrigerator Ice Maker Not Working? Here’s the Fix!
- 5 Reasons for Samsung Refrigerator Ice Maker Not Working (How To Fix)
Kenmore Ice Maker Not Turning?
If your ice maker isn’t turning, it could be because of a few different things. Here are some causes and solutions to help you get to the bottom of the problem.
One possible reason why your Kenmore ice maker is not turning is because the power supply has been disconnected. Check to make sure that the power cord is plugged into a working outlet. If it is, then the next thing to check is the circuit breaker. Flip the switch back and forth a few times to see if that does the trick.
If your ice maker still isn’t turning, then there could be an issue with the ice maker itself. One thing you can try is unplugging it for a few minutes and then plugging it back in. This can sometimes reset the ice maker and get it working again.
Kenmore ice maker auger not turning?
Here are some potential causes and solutions.
One potential cause is that the ice maker’s water supply is not turned on. Make sure that the shut-off valve for the water supply is in the “on” position. Another potential cause is a frozen ice maker auger. If this is the case, simply thaw out the auger by running hot water over it.
Is there a reset button on my Kenmore ice maker?
There’s no reset button on your Kenmore ice maker, but there are a few things you can do to try to get it working again. First, make sure that the ice maker is turned on and that the water supply is connected.
If the ice maker still isn’t working, try unplugging it for a few minutes and then plugging it back in. If that doesn’t work, you may need to replace the ice maker. You can find replacement ice makers at most major home improvement stores.
How to manually reset a Kenmore ice maker.
If your Kenmore ice maker isn’t working properly, you may need to reset it. To do this, simply unplug the ice maker for 30 seconds and then plug it back in. This should reset the ice maker and get it working again.
Kenmore ice maker not working but water dispenser is?
This is a common problem, and there are a few possible causes.
One possibility is that the ice maker’s water supply is not turned on. Another possibility is that the ice maker itself is not turned on. Finally, it could be that there is something blocking the ice maker’s water line.
The first thing to check is whether the ice maker’s water supply is turned on. If it is not, turn it on and wait a few hours to see if the ice maker starts working.
If the water supply is turned on and the ice maker still does not work, check to see if the ice maker itself is turned on.
Sometimes the switch can be accidentally turned off. If the ice maker is turned on and there is still no ice, it is likely that there is something blocking the ice maker’s water line.
The best way to clear a blocked water line is to use a small length of flexible tubing to blow air into the line. This will push any obstructions out of the way and allow the water to flow freely again. Once the line is clear, the ice maker should start working properly.
If you have followed all of these steps and the ice maker still does not work, it may need to be replaced. Fortunately, Kenmore offers a one-year warranty on all of its appliances, so if your ice maker is less than a year old, you should be able to get a replacement free of charge.
Kenmore refrigerator ice maker not working and red light blinking?
Here are some possible causes and solutions.
First, make sure that the ice maker is turned on. If it is, then check to see if there is ice in the tray. If there is no ice, then the problem may be with the water supply. Make sure that the water line is connected and that there is water flowing to the ice maker.
If the ice maker is turned on and there is ice in the tray, but the red light is still blinking, then the problem may be with the auger motor. This part of the ice maker helps to move the ice from the tray into the bin. If this motor is not working, then the ice will not be moved and the red light will continue to blink.
If the auger motor is not the problem, then the issue may be with the ice maker itself. If this is the case, then it will need to be replaced.
Kenmore refrigerator ice maker not working after power outage?
Check your home’s power. If the power is out, the ice maker will not work. Check to see if there is a power outage in your area by visiting your local utility company’s website or calling their customer service number.
If the power is on and your ice maker still isn’t working, it could be due to a faulty water line. Check to see if the water line is properly connected to the ice maker. If it isn’t, you’ll need to call a plumber to fix the issue.
If the power is on and the water line is connected, but your ice maker still isn’t working, it could be due to a clogged filter. Try replacing the filter and see if that fixes the issue.
Kenmore refrigerator Not Making Ice After Changing Filter?
Here are some possible causes and solutions.
-Check to see if the ice maker is turned on. The ice maker has an on/off switch. If it is in the “on” position, flip it to the “off” position and then back to the “on” position.
-If your refrigerator has a water filter, make sure that it is properly installed and that the filter is not clogged. A clogged water filter can restrict water flow to the ice maker, causing it to stop working.
-There may be an issue with the water line that supplies water to the ice maker. Check to see if the water line is kinked or frozen. If the water line is kinked, straighten it out. If the water line is frozen, thaw it out with a hair dryer.
-There could be a problem with the ice maker itself. If none of the above solutions work, you may need to replace the ice maker.
Kenmore elite refrigerator ice maker not working?
This can be a very frustrating issue. The good news is that there are some things you can do to try and fix the problem. In this article, we will go over some of the potential causes of why your Kenmore elite refrigerator ice maker not working as well as some solutions to try.
One potential reason why your Kenmore elite refrigerator ice maker not working could be because the ice maker is turned off. To check if this is the case, look for a switch on the ice maker itself or in the refrigerator near the ice maker. If the switch is in the “off” position, turn it to “on” and wait 24 hours to see if that fixes the problem.
Another potential reason why your Kenmore elite refrigerator ice maker not working is because the water supply to the ice maker has been turned off. To check if this is the case, locate the water shut-off valve behind the refrigerator and make sure it is in the “on” position. If it is in the “off” position, turn it to “on” and wait 24 hours to see if that fixes the problem.
If neither of these solutions fix the problem, then it is likely that there is an issue with the ice maker itself and you will need to call a Kenmore service technician to come and take a look at it.
Kenmore french door ice maker not working?
Here are some possible causes and solutions.
-First, check to make sure that the ice maker is turned on. The switch is usually located near the ice maker itself or in the freezer compartment. If it is turned off, turn it on and wait 24 hours to see if the ice maker begins working.
-If the ice maker is turned on, check to see if there is water available to the ice maker. There should be a water line connected to the back of the refrigerator. Make sure that the valve supplying water to this line is turned on all the way.
-If there is water available to the ice maker and it still isn’t working, it may be because the ice maker isn’t level. The ice maker needs to be level in order for it to work properly. Use a level to check and adjust the legs of the refrigerator until the ice maker is level.
Conclusion
If your Kenmore refrigerator ice maker is not working, there are a few things you can do to try and fix it. First, check to see if the ice maker is turned on. If it is, then you will need to check the water line to make sure it is not frozen. Finally, if none of these solutions work, you may need to call a professional for help.
We hope this article was helpful in troubleshooting your Kenmore refrigerator ice maker.