10 Reasons Why Kenmore Washer Not Draining: How to Fix

Last Updated on September 21, 2022 by Jason Nguyen

If your Kenmore washer isn’t draining, don’t worry – you’re not alone. This is a common problem that many people experience.

In this blog post, we will discuss the causes of this problem and how to troubleshoot and fix it. We will also provide some helpful tips on how to prevent this issue from happening in the future.

Kenmore Washer Not Draining: How to Troubleshoot and Fix

1. Drain Pump

If your Kenmore washer is not draining, the first thing you should check is the drain pump. The drain pump is responsible for pumping water out of the washer and into the drain hose. If the pump is clogged or damaged, it will need to be replaced.

There are a few things that can cause the drain pump to fail. If the washer is not draining properly, it could be because the pump is dirty or clogged. The pump may also be damaged or worn out.

If you suspect that the drain pump is the problem, you can try cleaning it first. If that doesn’t work, you will need to replace the pump. You can buy a new pump from most appliance stores or online retailers.

When replacing the drain pump, be sure to follow the instructions in the owner’s manual. This is a relatively easy repair that you can do yourself, but it’s always best to consult the manual before performing any repairs.

2. Clogged Pump or Hose

A Kenmore washer not draining can have a few different causes. The most common is a clogged pump or hose. If your washer won’t drain, check the pump and hose for any blockages.

How to fix it?

If your washer won’t drain, the first thing you should do is check the pump and hose for any blockages. If you find a clog, you can try to remove it with a plunger or a plumber’s snake. If that doesn’t work, you may need to replace the pump or hose.

3. Door Lock Motor and Switch Assembly

The door lock motor and switch assembly is located behind the washer tub, on the back of the washer. The door lock motor turns the door lock switch on and off. If the door lock motor is defective, the washer will not start.

To check the door lock motor:

Unplug the washer. Remove the screws that secure the back panel to the washer. Disconnect the wires from the door lock motor. Remove the door lock motor from the washer.

If the door lock motor is defective, replace it. If the door lock motor is not defective, check the door switch.

4. Lid Switch Assembly

The lid switch assembly is located on the top of the washer. If the washer lid is opened, the switch will be activated and the washer will stop. The lid switch can also be activated if the washer is not level.

To check if the lid switch is defective, open the lid and see if the washer stops. If the washer does not stop, the lid switch is defective and will need to be replaced.

Replacing the lid switch is a relatively easy task that can be completed in about an hour. The most important thing to remember when replacing the lid switch is to unplug the washer first!

Once you have unplugged the washer, you will need to remove the screws that hold the lid switch in place. After the screws have been removed, you can then pull out the old lid switch and replace it with the new one. Be sure to line up the screw holes before screwing in the new lid switch.

Once you have replaced the lid switch, you can then plug the washer back in and test it out. If the washer still does not work, you may need to check the wiring to see if there are any loose connections.

5. Water Pump Belt

The water pump belt on your Kenmore washing machine is responsible for pumping the water out of the tub and into the drain hose. If this belt becomes damaged or worn, it can cause the washer to stop draining properly.

You can check the condition of the water pump belt by removing the access panel from the back of the washer. The belt will be located around the water pump pulley. If the belt is cracked or frayed, it will need to be replaced.

Replacing the water pump belt is a relatively simple repair that can be completed in about 30 minutes. You will need a few basic tools, including a socket wrench and a Phillips head screwdriver.

6. Coin Trap

The coin trap is a feature on your Kenmore washer that helps to catch anything that could potentially clog the drain. This could be things like coins, hair ties, or other small objects.

The coin trap is located under the washer tub and can be accessed by removing the kickplate.

If your Kenmore washer is not draining properly, it is possible that there is something caught in the coin trap. To clean out the coin trap:

-Remove the kickplate by unscrewing the two screws that hold it in place.

-Locate the coin trap and remove any objects that may be blocking it.

-Replace the kickplate and screw it back into place.

How to prevent it happen again?

To prevent objects from getting caught in the coin trap, it is important to regularly clean out the trap. This can be done by removing the kickplate and emptying out the trap as needed.

You should also make sure that any objects that could potentially clog the drain are kept away from the washer. This includes things like coins, hair ties, and other small objects.

7. Drain Hose

If your Kenmore washer is not draining, the first thing you should check is the drain hose. The drain hose is responsible for carrying the water from the washer to the drainage pipe.

If there is a blockage in the hose, it will cause the water to back up and eventually overflow.

To clean the drain hose:

Unplug the washer from the power outlet.
Remove the drain hose from the drainage pipe.
Use a straightened coat hanger to clear any blockages.
Rinse the hose with water and reattach it to the drainage pipe.
Plug the washer back in and turn it on.

8. Door Lock

If your washer doesn’t start, the door lock might be defective. This is a very common problem. The door lock is an important safety feature on your washer. If it’s not working properly, your washer could start unexpectedly and injure you or someone else.

There are a few things you can do to test whether or not the door lock is defective. First, try pressing and holding the door lock button for a few seconds. If the washer doesn’t start, then the door lock is probably not the problem.

How to fix it?

If the door lock is defective, you’ll need to replace it. This is a pretty easy repair that most people can do themselves.

You can find replacement door locks at most home improvement stores or online. Be sure to get the right one for your model of washer. Once you have the new door lock, simply follow the instructions in your washer’s manual to install it.

9. Pump Motor

The pump motor in your Kenmore washing machine is responsible for pumping water out of the washer during the spin cycle. If your washer is not draining properly, the pump motor may be to blame.

How to test it?

To test the pump motor, first unplug the washing machine from the power outlet. Then, remove the drain hose from the back of the washer.

Next, use a multimeter to test continuity between the two terminals on the pump motor. If there is no continuity, then the pump motor is defective and will need to be replaced.

10. Water level valve

If your Kenmore washer is not draining, the water level valve may be the issue. This valve controls how much water is allowed into the washer during each cycle.

If it’s not working properly, water can build up in the washer and cause all sorts of problems.

Luckily, this is an easy problem to fix. Simply replacing the water level valve should do the trick. You can find replacement valves at most hardware stores or online.

Related:

Kenmore washer not draining and making noise?

Kenmore washer not draining and making noise? Here are some possible causes and solutions:

-A clogged drain hose or pump can cause your washer to not drain properly. To clean the drain hose, remove it from the washer and flush it out with a garden hose. If the pump is clogged, you may need to replace it.

-A problem with the drive belt or pulleys can cause your washer to make noise. To fix this, you will need to replace the drive belt or pulleys.

-If you have a Kenmore washer that is not draining and making noise, there are a few possible causes and solutions. By troubleshooting the problem, you should be able to fix it yourself.

Kenmore washer not draining completely?

There are a few things that could be causing this. Check the following:

-The washer is not level. Use a level to check and adjust the legs accordingly.

-There is something blocking the drainage hose. Remove the hose and clean it out.

-The drain pump may be damaged or dirty. Clean or replace the pump as needed.

Kenmore Series 70 Washer Won’t Drain?

If your Kenmore Series 70 washing machine isn’t draining properly, there could be a few different reasons why. Here are some possible causes and how to fix them so you can get your laundry done without any issues.

One possible reason why your washer might not be draining properly is because the drain hose is clogged. If this is the case, you’ll need to clean out the drain hose to get rid of any debris that might be blocking it.

Another possible reason for a clogged drain hose is if there’s a kink in it. Make sure to check your drain hose for any kinks or bends that could be causing a blockage.

If neither of these seem to be the problem, then it’s possible that the pump is defective and will need to be replaced.

Kenmore 80 series washer not draining?

If your Kenmore 80 series washer is not draining, there could be a few different reasons why. One possibility is that the drain hose is clogged.

Another possibility is that the pump itself is not working properly. If you suspect either of these issues, you should first try unplugging the washer and then clearing the drain hose. If that doesn’t work, you may need to replace the pump.

If your Kenmore 80 series washer is not draining, there are a few possible causes. One possibility is that the drain hose is clogged. Another possibility is that the pump itself is not working properly. If you suspect either of these issues, you should first try unplugging the washer and then clearing the drain hose. If that doesn’t work, you may need to replace the pump.

Another possibility is that the washer is not level. If your washer is not level, it can cause draining problems. You can check to see if your washer is level by using a level. Place the level on top of the washer and see if it is level from front to back and from side to side. If it is not level, you will need to adjust the legs until it is level.

If your Kenmore 80 series washer is still not draining, there could be an issue with the water inlet valve. The water inlet valve is what allows water to enter the washer. If there is a problem with the water inlet valve, it could cause your washer not to drain properly.

You can check the water inlet valve by unplugging the washer and then removing the hose from the valve. Turn on the water and see if water is coming out of the valve. If it is, then the valve is working properly. If not, you will need to replace the valve.

Kenmore 90 series washer not draining?

If your Kenmore 90 series washing machine is not draining, there are a few possible causes. The first thing to check is the drain hose. If the hose is kinked, it could be preventing water from draining properly.

Another possibility is that the drain pump has failed. If the pump is not working, water will not be able to drain from the washing machine. Finally, the drain filter may be clogged. If the filter is blocked, water will not be able to pass through it and will back up in the washing machine.

If your Kenmore 90 series washing machine is not draining properly, there are a few things you can try to fix the problem. First, check the drain hose to make sure it is not kinked. If it is, straighten it out and see if that fixes the problem.

If the hose is not the issue, try checking the drain pump. If the pump is not working, you may need to replace it. Finally, if all else fails, check the drain filter. If it is clogged, clean it out and see if that fixes the problem.

Kenmore Elite washer not draining?

If your Kenmore Elite washer is not draining properly, there could be a few different reasons why. In this blog post, we’ll go over some of the potential causes for a Kenmore Elite washer not draining and how to fix them.

One potential reason for a Kenmore Elite washer not draining is that the drain pump has failed. The drain pump is responsible for pumping the water out of the washer tub. If the drain pump has failed, you will need to replace it.

Another potential reason for a Kenmore Elite washer not draining is that the drain hose is clogged. The drain hose is what carries the water from the washer tub to the drain. If the drain hose is clogged, the water will not be able to flow through it and will back up into the washer tub. To fix this, you will need to clear the clog from the drain hose.

Kenmore Washer Stuck on Drain Cycle?

If your Kenmore washing machine is stuck on the drain cycle, there are a few possible reasons why.

One possibility is that the washer isn’t draining properly. This could be due to a clog in the drain hose or pump.

Another possibility is that the washing machine’s timer is stuck. This can be caused by a power surge or other electrical issue.

If your washing machine’s timer is stuck, you’ll need to reset it. Finally, there could be an issue with the washer’s control panel. This could be due to a faulty switch or another problem.

If your Kenmore washing machine is having any of these issues, it’s best to call a repairman. They’ll be able to diagnose the problem and fix it quickly.

Kenmore Washer Keeps Draining

1. Washer Drain

If your Kenmore washing machine doesn’t have a laundry center, it probably has a standpipe. The standpipe is a vertical pipe that drains the water out of the washer and into the home’s sewer system.

If the standpipe isn’t draining properly, the water will back up into the washer and cause it to overflow.

There are a few things you can do to clear a clogged standpipe. First, try using a plunger to unclog the pipe. If that doesn’t work, you can try using a plumbers’ snake to clear the blockage. If neither of those methods works, you may need to call a plumber to clear the standpipe.

2. Control Board

The control board is the brains of the washer. It tells the motor when to run and how fast, and it also controls the timer. If your washer isn’t draining properly, it could be because the control board is faulty.

To check if the control board is working properly, first make sure that all the connections are tight. If they are, then you’ll need to test the control board itself. You can do this with a multimeter.

If the control board is faulty, you’ll need to replace it. Fortunately, this is a relatively easy repair that you can do yourself. Just be sure to unplug the washer before beginning any work.

Conclusion

We hope this article helped troubleshoot your Kenmore Washer that is not draining. Remember to check the simple things first like ensuring nothing is blocking the drain hose before calling for service.

If you have checked all of these things and your washer is still not draining, it may be time to call a professional. Thanks for reading!