20 Reasons Why Kenmore Washer Not Spinning: How to Fix

If your Kenmore washer isn’t spinning, don’t worry – you’re not alone. This is a common problem that can be fixed relatively easily. In this blog post, we will walk you through the steps to take to get your washer spinning again. We will also provide some tips on how to prevent this from happening in the future.

Related: 7 Washing Machine Brands To Avoid and 3 Most Reliable Brands

Kenmore Washer Not Spinning: How to Fix

1. Wash Cycle and Spin Setting

Make sure that you have selected the correct cycle and spin setting for your load. Some cycles, like the delicate cycle, don’t spin as quickly as others.

2. Lid Switch Assembly

The lid switch assembly is a safety device that keeps the washer from spinning when the lid is open.

If your Kenmore washer does not spin, it may be because the lid switch assembly is defective.

You can replace the lid switch assembly yourself with a few tools and some basic knowledge of how to use them.

To replace the lid switch assembly, you will need:

-A screwdriver

-A putty knife

-A new lid switch assembly

First, use the screwdriver to remove the two screws that hold the lid switch assembly in place. Then, use the putty knife to pry the old lid switch assembly out of its housing. Be careful not to damage the housing.

Next, insert the new lid switch assembly into the housing and secure it with the two screws. Test the washer to make sure that it is now spinning properly. If it is not, you may need to consult a repair manual or call a professional for help.

3. Drive Belt

The drive belt is a rubber belt that connects the motor to the spin basket. If the drive belt is broken, then the washer will not be able to spin.

Replacing the drive belt is a fairly easy repair that can be done by most do-it-yourselfers. The first thing you need to do is unplug the washer from the power source. Next, you will need to remove the back panel of the washer. Once the back panel is removed, you will be able to see the drive belt.

To replace the drive belt, simply remove the old belt and put on a new one. Make sure that the new belt is tight before putting the back panel back on.

Once the back panel is in place, plug the washer back in and give it a try. If the washer still does not spin, then you may have a problem with the motor.

4. Motor Coupling

The motor coupling connects the motor to the washer tub. If the coupling is worn out or damaged, it can cause the washer not to spin.

How to fix it:

You will need to replace the motor coupling. This is a relatively easy repair that you can do yourself. You can find the motor coupling at your local hardware store.

To replace the motor coupling, first, remove the power to the washer. Next, remove the screws that hold the motor in place. Once the motor is removed, you will be able to access the coupling.

To install the new coupling, simply reverse the process. Be sure to tighten the screws securely so that the motor does not come loose during operation.

5. Door Latch

If your washing machine door won’t close or latch, there could be a problem with the door switch. The door switch signals the washing machine to start and stop working.

If the door switch is damaged or defective, it may not signal the washing machine to start. You can test the door switch with a multimeter to see if it’s defective.

To test the door switch:

  • Unplug the washing machine.
  • Remove the screws that hold the door switch in place.
  • Use a multimeter to test the continuity of the door switch.
  • If the door switch is defective, replace it with a new one.

How to prevent it?

Regularly check the door switch for damage or wear and tear. If the door switch is damaged, replace it immediately.

6. Door Lock Motor and Switch Assembly

The door lock motor and switch assembly is located behind the control panel on your Kenmore washing machine. This part is what locks the door of your washer so that water cannot come out while the washer is running. If this part is broken, your washer will not be able to spin.

You can replace the door lock motor and switch assembly yourself, but it is a bit of a challenge. You will need to remove the control panel first, and then you will have to access the door lock motor and switch assembly.

Once you have accessed the door lock motor and switch assembly, you will need to disconnect the wires that are attached to it. After that, you can remove the door lock motor and switch assembly and replace it with a new one.

7. Motor Control Board

The Motor Control Board is the “brains” of the washing machine. It tells the motor when to start and stop. If this board fails, the washer will not spin.

To check if your Motor Control Board is faulty:

First, check if there are any error codes displayed on your washing machine. If you see an error code, it is likely that the Motor Control Board is faulty.

Next, check the electrical supply to the washing machine. Make sure that the power cord is plugged into a working outlet and that the circuit breaker has not been tripped. If the power is off, the Motor Control Board will not be able to function.

If the washing machine is getting power but still not spinning, it is likely that the Motor Control Board is faulty and will need to be replaced.

Replacing the Motor Control Board is a relatively simple process. You can find replacement boards online or at a local appliance parts store. Be sure to get the correct board for your model of washing machine.

Once you have the replacement board, follow these instructions:

-First, unplug the washing machine from the power outlet.

-Next, remove the back panel of the washer. This will give you access to the Motor Control Board.

-Remove the old board and replace it with the new one.

-Reattach the back panel and plug the washing machine back into the power outlet.

-Turn on the washing machine and check to see if it is now spinning properly.

How to prevent it?

To prevent your washing machine from experiencing this issue, be sure to keep the area around the machine clean and free of debris. Also, do not overload the washer as this can put strain on the motor and cause it to fail.

8. Clutch

The clutch on a Kenmore washer is what helps to transition the agitator from one speed to another. If your washer isn’t spinning, it could be because the clutch is worn out. Replacing the clutch is a relatively easy repair that you can do yourself.

To see if the clutch is the problem, first remove the agitator from the washer. With the agitator removed, you should be able to see the clutch. Inspect the clutch for any signs of wear or damage. If the clutch looks damaged, it will need to be replaced.

How to prevent it?

You can prevent this problem by regularly cleaning your washer. Be sure to remove any lint or debris that may have accumulated around the agitator and clutch. This will help to keep the parts working properly and prevent them from wearing out prematurely.

9. Clutch Band Kit

The Clutch Band Kit is a kit that helps to repair a washing machine. The kit includes a new clutch band, washer tub, and safe-for-washing machine cleaner.

The band goes around the tub and helps to prevent clothes from getting tangled in the spinning process.

The kit also contains a new washer tub that is made of durable plastic and is safe for use in a washing machine.

The kit also includes a safe-for-washing machine cleaner that helps to clean the washer tub and keep it looking new.

10. Drive Pulley

The drive pulley is an important part of your Kenmore washer. If this piece breaks, the washer will not spin. This can be a very costly repair. Luckily, there are some things that you can do to prevent this from happening.

First, make sure that you keep the drive pulley clean. If there is any dirt or debris on it, this can cause the pulley to break. Second, be sure to check the tension on the drive belt regularly. If the belt is too loose, this can also cause the pulley to break.

If you do find that the drive pulley is broken, you will need to replace it. This is not a difficult repair, but it is one that should be done by a qualified technician.

If you follow these simple tips, you can help prevent the drive pulley from breaking on your Kenmore washer.

11. Rotor Assembly

The rotor assembly is located inside the washer tub and is what helps to spin the clothes during the wash cycle. If this part is not working properly, it can cause the washer to not spin.

There are a few things that you can do to try and fix this problem on your own. First, check to make sure that the washer is level. If it is not, then it can cause the washer to not spin correctly.

You can also try and clean the rotor assembly with a soft cloth. If neither of these things work, then you will need to call a repairman to come and take a look at your washer.

12. Stator Assembly

The stator assembly is located beneath the washer tub. The function of the stator assembly is to keep the washer tub from moving during the spin cycle. If your Kenmore washer is not spinning, it may be because the stator assembly has failed.

You can check for a broken stator assembly by opening up the washer and inspecting the part. If the stator assembly is broken, you will need to replace it.

Replacing the stator assembly is a relatively easy repair that you can do yourself. You will need to purchase a new stator assembly from a Kenmore dealer or an online retailer. Once you have the new part, simply remove the old stator assembly and install the new one in its place.

13. Bearing

The washer’s bearings help to keep the inner tub stable as it spins. If your washer is not spinning, it could be due to a problem with the bearings. You will need to replace the bearings if they are damaged.

How to fix:

If you have a Kenmore washer that is not spinning, you will need to replace the bearings. You can do this yourself if you have the right tools and knowledge. However, it is best to leave this task to a professional.

14. Rear Drum with Bearing

If your Kenmore washer is not spinning, it may be due to a problem with the rear drum. The rear drum is what the clothes are actually washed in and it is supported by a bearing.

Over time, this bearing can wear out and cause the drum to become unbalanced. This can lead to the washer not spinning properly.

If you think that the problem with your Kenmore washer is due to a worn-out rear drum bearing, you will need to replace it. This is not a difficult repair, but it will require some disassembly of the washer. You will also need to purchase a new rear drum bearing. These are available at most appliance parts stores.

With a few tools and the new rear drum bearing, you can replace the old one and get your Kenmore washer spinning properly again. Just be sure to follow the instructions carefully so that you do not damage the new bearing.

15. Tub Bearing

The tub bearing is located under the tub, on the back of the washer. The tub bearing helps to keep the inner tub spinning smoothly.

This part can wear out over time, causing a thumping noise during the spin cycle. If your washer is making this noise, it’s important to replace the tub bearing.

You can do this repair yourself, but it’s a fairly difficult repair. We recommend that you hire a professional to do the job for you.

16. Tub Seal and Bearing Kit

The Tub Seal and Bearing Kit is an easy to install replacement part for your Kenmore washing machine. This kit includes a new tub seal and bearings that will help keep your washer spinning smoothly.

If your Kenmore washer is not spinning, the first thing you should check is the Tub Seal and Bearing Kit. This easy to install replacement part can help keep your washer spinning smoothly and prevent leaks.

To install the Tub Seal and Bearing Kit, simply follow these instructions:

  • Unplug your washing machine from the power outlet.
  • Remove the back panel of your washing machine.
  • Disconnect the hoses from the tub.
  • Remove the old tub seal and bearings.
  • Clean the surface of the tub.
  • Install the new tub seal and bearings.
  • Reconnect the hoses to the tub.
  • Replace the back panel of your washing machine.
  • Plug your washing machine back into the power outlet.

17. Basket Drive

The Kenmore washer not spinning is a common problem with front load washers. The basket drive is located on the back of the washer and is what drives the washing action. If this becomes damaged, it can cause the washer to not spin properly.

There are a few things that you can do to try and fix this problem. First, you will want to check the basket drive for any damage. If there is any damage, you will need to replace it.

How to prevent it?

You can prevent this problem by making sure that the basket drive is properly maintained. You should clean it regularly and make sure that there are no damaged parts. You should also make sure that the washer is level so that the basket drive does not become misaligned.

18. Drive Motor

The drive motor is one of the most important parts of your washer. It is responsible for turning the drum and agitator during the wash cycle. If your washer is not spinning, it could be due to a problem with the drive motor.

There are a few things that you can do to troubleshoot this problem. First, check to make sure that the drive belt is not broken. If the drive belt is broken, it will need to be replaced. Another thing to check is the state of the drive motor itself. If the motor is burned out, it will need to be replaced.

19. Transmission

If your Kenmore washing machine is not spinning, it may be due to a problem with the transmission.

The transmission is responsible for connecting the motor to the agitator and spin basket. If there is an issue with the transmission, it can prevent the washer from spinning properly.

There are a few things you can do to troubleshoot the issue. First, check to see if anything is blocking the path of the spin basket. If there is, remove it and try again. Next, check the transmission for any signs of damage or wear. If you see any damage, it will need to be replaced.

20. Door Lock

If your Kenmore washer doesn’t start the spin cycle or locks during a cycle, it could be due to a faulty door lock. In this article, we’ll show you how to troubleshoot and replace a faulty door lock on your Kenmore washing machine.

Door locks on washing machines are designed to keep the door closed during operation. The door lock can become faulty over time, causing the washer to either not start the spin cycle or to stop mid-cycle.

If you’re having problems with your Kenmore washing machine, follow these troubleshooting tips to fix a faulty door lock.

First, check that the door is properly latched. If the door is not properly latched, the door lock will not engage and the washer will not start. To fix this, simply close the door and make sure that it is properly latched.

If the door is properly latched and the washer still doesn’t start, then the problem may be with the door lock itself. To test this, open the door and try to manually engage the door lock. If the door lock is difficult to engage or if it doesn’t stay engaged, then it will need to be replaced.

Replacing a washing machine door lock is a relatively easy repair that can be done in about an hour. Follow these steps to replace a faulty door lock on your Kenmore washing machine.

First, disconnect the power to the washing machine. Next, remove the screws that hold the door lock in place. Then, remove the old door lock and replace it with a new one. Finally, screw the new door lock in place and reconnect the power to the washing machine.

Related:

Kenmore washer not spinning fast enough?

One possible reason why your Kenmore washer is not spinning fast enough could be that the load of laundry is too small. Try adding a few more items to the load and see if that makes a difference.

Another possibility is that something is blocking the washer’s spin cycle. Check to make sure that there is nothing caught in the washing machine’s drum or blocking the spin cycle hose.

Kenmore Washer Spins Slowly?

One of the most common reasons a washing machine will spin slowly is that the load is unbalanced. This can be caused by too many clothes in one area of the tub or not enough clothes in another area. To fix this, simply redistribute the clothing evenly around the tub and try spinning again.

Another possible cause is that the washing machine’s settings are not properly configured. The spin speed setting may be set too low or there may be something blocking the spinning mechanism.

To fix this, check the washing machine’s settings and make sure everything is properly configured. If there are any obstructions, remove them and try spinning again.

Kenmore washer not spinning coupler is good?

Let’s take a look at some of the most common causes and how to fix them.

One of the most common reasons why a Kenmore washer might not spin is that the coupler is damaged or broken. The coupler is what connects the motor to the washing machine, so if it’s damaged, the motor won’t be able to spin the drum.

To check if the coupler is the problem, take a look at it and see if there are any cracks or damage. If you see any damage, you’ll need to replace the coupler.

Another common reason why a Kenmore washer might not spin is that the belt is damaged or broken. The belt helps to spin the drum, so if it’s damaged, the washer won’t be able to spin. To check if the belt is the problem, take a look at it and see if there are any cracks or damage. If you see any damage, you’ll need to replace the belt.

If neither of these are the problem, then there may be something wrong with the motor. If you think this might be the case, you’ll need to take the washer to a professional to have it checked out.

Kenmore washer not spinning clothes dry enough?

If your Kenmore washer isn’t spinning clothes dry enough, there are a few things that could be causing the issue. Here are some of the most common causes:

-A clogged lint filter: A clogged lint filter can restrict air flow and cause your clothes to come out wetter than they should. Be sure to clean your lint filter regularly.

-An overloaded washer: Overloading your washer can cause clothes to come out wetter than they should. Be sure not to overload your washer and follow the manufacturer’s instructions.

-A worn out pump: A worn out pump can’t move water as effectively, which can cause clothes to come out wetter than they should. Be sure to check your pump regularly and replace it if necessary.

If you’re still having trouble, there are a few things you can try:

-Run a maintenance cycle: This will clean the washer and help remove any build-up that could be causing the issue.

-Check the hoses: If the hoses are kinked or damaged, they may not be able to move water properly. Be sure to check them and replace them if necessary.

Kenmore washer not spinning water out of clothes?

If your Kenmore washer is not spinning water out of clothes, there are several possible causes. To troubleshoot and fix the problem, follow these steps.

If your Kenmore washer is not spinning water out of clothes, there are several possible causes:

-The washer may be unlevel. Check to make sure that the washer is level and not tilted.

-The load of laundry may be too small or too large. Try washing a smaller or larger load of laundry to see if that makes a difference.

-There may be something blocking the washer from spinning. Check for any objects that may be blocking the washer, such as coins or buttons.

-The washer may need to be reset. Unplug the washer for 30 seconds, then plug it back in and try again.

Kenmore washer won’t spin or agitate just buzzes hums?

Here are some possible causes and how to fix them.

The first thing to check is if the washer is plugged in correctly and that there is power going to it. If the washer is plugged in and there is still no power, you may need to replace the fuse or reset the circuit breaker.

If there is power to the washer, the next thing to check is the drive belt. The drive belt is what turns the agitator and the spin cycle. If the drive belt is loose or damaged, it will need to be replaced.

Another possible cause of a washer not spinning or agitating is a problem with the lid switch. The lid switch prevents the washer from spinning or agitating when the lid is open. If the lid switch is damaged or defective, it will need to be replaced.

If your washer is still not spinning or agitating, it may be because the transmission is damaged. The transmission is what powers the spin cycle and if it is damaged, it will need to be replaced.

Kenmore washer not spinning and making loud noise?

Kenmore washer not spinning making loud noise is a fairly common problem. There are several possible causes, and each one has its own solution. In this article, we’ll go over the most common causes and how to fix them.

The first thing to check is the washing machine’s lid switch. The lid switch is a safety feature that keeps the washer from spinning when the lid is open. If the lid switch is defective, the washer will not spin.

The second thing to check is the drive belt. The drive belt is a rubber belt that connects the motor to the washing machine’s spin basket. If the drive belt is broken or loose, it will cause the washing machine to make a loud noise and not spin.

Third, check the washing machine’s clutch. The clutch is what engages the washer’s spin basket with the drive belt. If the clutch is worn out, it will cause the washing machine to make a loud noise and not spin. Fourth, check the washing machine’s motor. The motor is what powers the washing machine’s spin basket. If the motor is defective, it will cause the washing machine to make a loud noise and not spin.

Fifth, check the washing machine’s drive pulley. The drive pulley is a plastic or metal wheel that connects the motor to the drive belt. If the drive pulley is damaged, it will cause the washing machine to make a loud noise and not spin. Sixth, check the washing machine’s spin basket. The spin basket is where the clothes are placed during the wash cycle. If the spin basket is damaged, it will cause the washing machine to make a loud noise and not spin.

The last thing to check is the washing machine’s lid. The lid is what keeps the clothes in the spin basket during the wash cycle. If the lid is damaged, it will cause the washing machine to make a loud noise and not spin.

How do you reset a Kenmore washer that won’t spin?

If your Kenmore washer won’t spin, there are a few things you can try to reset it. First, unplug the washer from the power outlet and wait for 30 seconds. Then, plug the washer back in and press the “Start/Pause” button.

If the washer still doesn’t spin, open the lid and redistribute the load. Close the lid and press the “Start/Pause” button again. If your washer still won’t spin, you may need to call a technician for further assistance.

Conclusion

If your Kenmore washer is not spinning, there are a few potential causes. First, check to make sure that the washer is properly plugged in and that the power cord is not damaged. Next, check the water supply hoses to ensure that they are not kinked or blocked. Finally, inspect the washing machine’s lid switch to see if it is defective.

If you are still having trouble, contact a Kenmore service technician for assistance.