10 Reasons Why Hotpoint Washer Not Draining: How to Fix

If your Hotpoint washer is not draining, you are likely to experience a number of problems. Not only will your clothes take forever to wash, but the water will start to build up and could damage your machine. In this blog post, we will discuss some common causes of this problem and provide tips on how to fix it.

Related: 7 Washing Machine Brands To Avoid and 3 Most Reliable Brands

Why is my Hotpoint washer not draining?

1. Drain Pump.

If your Hotpoint washer is not draining, the first thing to check is the drain pump.

The drain pump helps to remove water from the washer tub. If the drain pump is defective, the washer will not be able to drain properly.

Why does it fail?

The drain pump can fail for a number of reasons. The most common reason is that the pump becomes clogged with lint or other debris. This can happen if you don’t clean the lint filter regularly.

Another common reason for pump failure is a broken impeller. The impeller is the part of the pump that helps to move water through the pump. If the impeller is broken, the pump will not be able to move water and will fail.

How do I fix it?

To test the drain pump, unplug the washer and remove the access panel. Locate the drain pump and check for any obstructions. If the pump is clear, try running the washer again. If the problem persists, you may need to replace the drain pump.

To replace the drain pump:

– Unplug the washer and shut off the water supply.

– Remove the access panel and disconnect the wires from the drain pump.

– Remove the screws that hold the pump in place and remove the old pump.

– Install the new pump and reconnect the wires.

– Replace the access panel and screw it in place.

– Plug in the washer and turn on the water supply.

– Run the washer to test it.

2. Clogged Pump or Hose.

The first thing you should check is the pump. The pump could be clogged with lint or other debris. If the pump is clear, then check the hoses. The hoses could be clogged with lint or other debris.

How to fix it?

If the pump is clogged, you will need to clean it out. You can do this by removing the pump and cleaning it with a brush. If the hoses are clogged, you will need to replace them.

You can find replacement hoses at your local hardware store or online.

3. Door Lock Motor and Switch Assembly.

The door lock motor and switch assembly is an important part of your Hotpoint washing machine. This part is responsible for locking the door of your washer, and it also helps to keep the water inside the tub from draining out.

If this part fails, your washer will not be able to operate properly. To replace this part, you will need to purchase a new door lock motor and switch assembly from your local Hotpoint dealer.

4. Drive belt.

The drive belt is the part of the washer that helps to rotate the drum. If this belt becomes damaged or broken, it can cause the washer to stop draining properly. You will need to replace the drive belt if it is damaged or broken.

You can find the drive belt on the underside of the washer. It is a long, skinny belt that is usually black or brown in color. If you cannot find the drive belt, you can always consult your Hotpoint washer manual for more information.

Once you have located the drive belt, you will need to remove it. To do this, simply unscrew the two screws that hold it in place. Once the screws are removed, you can pull the drive belt off of the washer.

Now, you will need to replace the drive belt with a new one. To do this, simply put the new drive belt in place and screw the two screws back into place. Once the screws are tightened, your Hotpoint washer should be able to drain properly again.

5. Lid Switch Assembly.

The lid switch assembly is located on the top of your washer. If the washer does not have a see-through lid, there will be a small hole on the top of the washer where you can insert a coin to manually release the lid lock.

If your Hotpoint washing machine is not draining, one possible reason is that the lid switch assembly is not working properly. The lid switch assembly is a safety feature that prevents the washer from spinning when the lid is open. If the lid switch assembly is defective, it may not allow the washer to spin or drain.

To test the lid switch assembly, open the top of your washing machine and watch for the indicator light. If the indicator light does not come on, then the lid switch assembly is likely defective and will need to be replaced.

6. Water Pump Belt.

The water pump belt on your Hotpoint washer is an important part of the machine. If the belt is not working properly, it can cause the washer to not drain properly. There are a few things that you can do to troubleshoot this problem.

First, check to see if the belt is loose. If it is, tighten it up. If the belt is still not working properly, you may need to replace it.

7. ‘Crease Care’ or ‘Rinse Hold’ setting is selected.

If your Hotpoint washing machine is not draining, it may be because you have selected one of these settings. The ‘Crease Care’ setting uses a lower spin speed to prevent clothes from creasing, while the ‘Rinse Hold’ setting keeps the water in the drum so that you can add more detergent or fabric softener.

To fix this problem, simply deselect these settings and your washing machine should start draining normally.

8. Coin Trap.

The coin trap is a plastic guard that covers the pump. It’s there to prevent things like coins from getting into the pump and causing it to fail. If your washer isn’t draining, check the coin trap first.

To access the coin trap:

– Unplug the washer from the power outlet.

– Remove the screws that hold the coin trap in place.

– Lift the coin trap out of the washer.

If there’s a coin or other object blocking the pump, remove it and clean out any debris. Replace the coin trap and screw it back into place. Plug the washer back in and restart your cycle.

9. Drain Hose.

If your Hotpoint washing machine isn’t draining properly, one potential cause could be a blockage in the drain hose.

The drain hose is the pipe that carries water and debris from the washer to the home’s drainage system.

A blocked drain hose can cause water to back up into the washer, resulting in poor draining and potentially flooding.

To check if the drain hose is the cause of your draining issue, first make sure that it isn’t kinked or bent. If it is, straighten it out. Next, check to see if there is any debris caught in the hose. If there is, remove it and clear the way for proper drainage.

10. Door Lock.

The door lock is an important safety feature on your Hotpoint washing machine. It prevents the washer from operating when the door is open. If your washer does not have a door lock, it will not be able to start or continue a cycle.

If you’re having trouble with your Hotpoint washer not draining, one possible issue is a faulty door lock. In this case, you’ll need to replace the door lock in order to get your washer up and running again.

Here’s what you’ll need to do:

– Unplug the washing machine from the power outlet.

– Remove the screws that hold the door panel in place.

– Disconnect the door lock wiring harness.

– Remove the door lock from the door panel.

– Install the new door lock in the reverse order.

Once you’ve replaced the door lock, your Hotpoint washer should be able to drain properly and continue functioning as normal.

Related:

Hotpoint washer not draining completely?

If your Hotpoint washer isn’t draining completely, there could be a few different reasons why. One possibility is that the drain hose is kinked or clogged. Another possibility is that the pump might be damaged or defective.

If you’re having this issue, here are a few things you can try to fix it:

-Clear the drain hose of any kinks or blockages.

-Make sure the pump is not damaged or defective. If it is, you will need to replace it.

-Check for any other clogs in the washing machine.

New Hotpoint washer not draining?

Don’t panic – there are a few things you can try before calling a repairman.

First, check the washer’s drain hose to make sure it isn’t kinked or clogged. If that doesn’t do the trick, then you may need to clean out the washer’s pump filter.

With a little troubleshooting, you should be able to get your washer up and running again in no time.

Hotpoint washer dryer fabric softener dispenser not draining?

You’re not alone. Many Hotpoint washer dryer owners have reported this issue.

The most common cause of the fabric softener dispenser not draining is a clogged filter. The filter is located in the bottom of the dispenser and can become clogged with lint, hair, and other debris. To clean the filter, remove it from the dispenser and rinse it with warm water. If the filter is excessively clogged, you may need to replace it.

Another possible cause of the fabric softener dispenser not draining is a blockage in the fabric softener line. The line can become blocked by lint, hair, and other debris. To clean the line, remove it from the dispenser and flush it with warm water. If the line is excessively blocked, you may need to replace it.

Hotpoint top load washer not draining?

If your washer won’t drain, there could be a few different reasons why. Check out this list of possible causes and solutions to see if you can fix the problem yourself.

If your Hotpoint top load washer is not draining, the first thing you should check is the drain hose. If the hose is kinked or clogged, that could be the problem. Try unkinking or clearing the hose and see if that fixes the issue.

Another possibility is that the pump is damaged or clogged. If you suspect this is the case, you’ll need to call a repairman to fix or replace the pump.

Finally, it’s possible that there is something caught in the drain pump. This can usually be fixed by taking the washer apart and cleaning out the drain pump. However, if you’re not comfortable doing this yourself, you’ll need to call a repairman.

Hotpoint Aquarius washer not draining?

This is a common problem that can be caused by a few different things. Here are some possible causes and solutions.

If your Hotpoint Aquarius washer is not draining, the first thing you should check is the drain hose. If the hose is kinked or blocked, it could be preventing water from draining properly. Another possibility is that the pump is clogged. If the pump is clogged, it will need to be cleaned or replaced.

If you have checked the drain hose and pump and they are not the problem, then the issue could be with the washing machine itself. If your washing machine is overloading, it can cause problems with draining. Try redistributing the load and see if that solves the problem. If your washing machine is still not draining, you may need to call a repairman.

How to empty a Hotpoint washing machine full of water?

If your Hotpoint washing machine is full of water, don’t panic! There are a few simple steps you can take to empty it out.

First, unplug the washing machine from the power outlet. Then, locate the drain hose and disconnect it from the back of the machine. Next, place a large bowl or bucket under the hose to catch the water. Finally, open the door of the washing machine and allow the water to drain out.

Once the water has finished draining, close the door and reconnect the drain hose. Finally, plug the machine back in and turn it on. Your Hotpoint washing machine should now be empty!

Conclusion

If your Hotpoint washer is not draining, there are a few things you can do to fix the problem. First, check the drain hose to make sure it is not kinked or clogged. Next, check the drain pump to see if it is dirty or blocked. Finally, if all else fails, you may need to call a professional to service your washer.

With a little troubleshooting, you should be able to get your Hotpoint washer draining properly in no time!