Last Updated on August 13, 2022 by Kimberly Crawford
If your GE washer isn’t draining, don’t worry – you’re not alone. This is a common problem that many homeowners face. In this blog post, we will discuss the causes of this issue and how to troubleshoot and fix it. We will also provide some tips to help prevent this from happening in the future.
Related: 7 Washing Machine Brands To Avoid and 3 Most Reliable Brands
Why GE Washer Not Draining? How to Troubleshoot and Fix
1. Clogged Drain Pump.
This is a very common problem with GE washers. The drain pump can become clogged with lint, hair, and other debris.
This will cause the washer to not draining properly. To fix this problem, you will need to clean out the drain pump.
To clean out the drain pump, you will need to remove the two screws that hold it in place. After the screws are removed, you will be able to pull out the drain pump. Be sure to unplug the washer before you begin this repair.
Once the drain pump is removed, you can clean it out with a brush or a vacuum cleaner. Be sure to get all of the debris out of the pump. Once you have cleaned out the pump, you can reinstall it and screw it back in place.
Why does it fail?
The most common reason for a washing machine drain pump to fail is because of a clog. The drain pump uses an impeller to force water through the drain hose.
If there is something blocking the impeller, it will not be able to do its job and the water will not be able to drain from the washer.
Another common reason for the drain pump to fail is because of a build-up of lint. Lint can get caught in the impeller and prevent it from turning. This will also cause the water to not be able to drain from the washer.
2. Coin Trap.
The coin trap is located in the bottom of the washer near the drain hose.
If a small object such as a coin, button, or paper clip falls into the wash tub, it may become lodged in the coin trap and cause the washer to stop draining.
Why does it fail?
The most common reason for a GE washer not draining is because the coin trap needs to be cleaned. The coin trap is a small plastic cup that sits under the washing machine’s drain pump.
Over time, lint and other debris can build up in the coin trap and block the drainage hole. As a result, water will back up into the washer and cause it to fail.
If your GE washer is not draining, you can try cleaning the coin trap yourself.
First, unplug the washing machine from the power outlet.
Then, remove the drain hose from the back of the machine and place it in a bucket.
Next, locate the coin trap and remove it from the machine.
Finally, rinse out the coin trap and replace it. If this does not solve the problem, you may need to call a professional for help.
3. Drain Pump Filter.
The first thing you’ll want to check if your GE washer is not draining is the drain pump filter. This is a small screen that filters out lint and other debris from the water as it drains from the washer.
If this filter becomes clogged, it can cause the washer to stop draining properly. To clean the filter, simply remove it from the washer and rinse it off with water.
If you see any lint or other debris on the filter, be sure to remove it before putting the filter back in place.
Why does it fail?
The most common reason for a drain pump filter to fail is because of a blockage. The blockage can be caused by anything from lint to dirt to small objects.
If your washer is not draining properly, check the drain pump filter for a blockage. You may need to use a toothbrush or other small object to clean out the filter. If the blockage is severe, you may need to replace the filter.
Another reason for a drain pump filter to fail is because it is clogged with soap scum. Over time, soap scum can build up and cause the filter to become clogged. This can cause your washer to not drain properly.
To clean a clogged drain pump filter, soak it in vinegar for a few hours. Then, use a toothbrush or other small object to scrub the filter. If the clog is severe, you may need to replace the filter.
4. Kinked or clogged Drain Hose.
If your GE washer is not draining, one possible reason is a kinked or clogged drain hose. This can happen if the hose is bent or crushed, or if there is something blocking the flow of water through it.
Why does it fail?
The drain hose is the tube that carries water from the washer to the drain. If this hose is clogged, water will back up into the washer and it will not be able to drain properly.
The most common cause of a clogged drain hose is lint. Lint can build up over time and eventually block the hose.
Another common cause of a clogged drain hose is a kink in the hose. A kink can occur if the hose is not installed properly or if it gets bent during use.
How to fix it?
Start by unplugging the washer and removing the drain hose from the back of the machine. Next, flush the hose out with water to remove any lint or debris that may be blocking it. If there is a kink in the hose, straighten it out.
Once the hose is clear, reattach it to the washer and plug the machine back in. Run a test load of laundry to see if the washer is draining properly. If not, you may need to call a technician for further assistance.
5. Door Lock.
The first thing you should check if your GE washer is not draining is the door lock. If the door lock is defective, it will prevent the washer from draining.
You can test the door lock by opening and closing the door of the washer. If the door lock is defective, you will need to replace it.
Why does it fail?
The most common reason for a GE washer not draining is that the door lock has failed.
This can be caused by a variety of things, including a power surge, a faulty wiring harness, or simply wear and tear. Sometimes, the door lock can be repaired, but in most cases it will need to be replaced.
How to fix it?
If the door lock is the problem, the first thing you should do is check the power supply. If there has been a power surge, it may have damaged the door lock.
If the power supply is fine, then check the wiring harness. If it is damaged, it will need to be replaced. Finally, if neither of these are the problem, then the door lock will need to be replaced.
Replacing the door lock is a fairly simple process. First, you will need to remove the old door lock. This can be done by unscrewing the two screws that hold it in place.
Next, you will need to install the new door lock. Simply screw it into place and then reconnect the wiring harness. Finally, test the door lock to make sure it is working properly.
6. Door Lock Motor and Switch Assembly.
If your GE washer is not draining properly, it could be due to a problem with the door lock motor and switch assembly.
This is a relatively easy problem to fix, and you should be able to do it yourself in just a few minutes.
Why does it fail?
The most common reason for the door lock motor and switch assembly to fail is because of a power surge. A power surge can cause the door lock motor and switch assembly to become damaged or even burn out.
Another reason for the door lock motor and switch assembly to fail is because of a faulty wiring connection. If the wiring connections are not correct, it can cause the door lock motor and switch assembly to fail.
Finally, if the door lock motor and switch assembly become wet, it can also cause the door lock motor and switch assembly to fail.
How to fix it?
First, unplug the washer from the power outlet. Then, remove the screws that secure the door lock motor and switch assembly to the washer. Carefully pull out the assembly, being careful not to damage any of the wires.
Once you have removed the door lock motor and switch assembly, check to see if the problem is with the door lock itself or with the switch. If it is with the door lock, you will need to replace it. If it is with the switch, you can either replace it or try to clean it and see if that solves the problem.
Finally, if the door lock motor and switch assembly is wet, you will need to dry it off before you can use it again.
Once you have fixed the problem, reassemble the door lock motor and switch assembly and screw it back into place. Then, plug the washer back in and turn it on. Your GE washer should now be draining properly.
7. Excess Sudsing.
If your GE washer is not draining, it could be due to excess sudsing. Sudsing can occur when there is too much soap or detergent in the wash water.
When this happens, the washer may not be able to remove all of the suds from the clothing. As a result, the clothing may become soaked with soapy water and take longer to dry.
To prevent excess sudsing, use only the amount of soap or detergent recommended by the manufacturer. You may also need to use a different type of soap or detergent if you are using a HE (high efficiency) washer. HE detergents are low sudsing and are designed for use in HE washers.
If you have already used too much soap or detergent, you can try running the washer again with just water to remove the suds. You may also need to clean the washer’s dispenser drawer to remove any soap buildup. Consult your owner’s manual for instructions on how to do this.
8. Drive Belt.
The drive belt is a rubber belt that goes around the entire washer. If this belt breaks, the washer will not be able to spin.
You can check the drive belt for wear by opening up the washer and inspecting it. If the drive belt is damaged, you will need to replace it.
Why does it fail?
The most common reason for a drive belt to fail is due to age and wear. The rubber can break down and deteriorate over time, causing it to snap.
Another reason for failure is if the washing machine is overloaded and the extra weight puts too much strain on the belt. Improper installation can also lead to a drive belt breaking prematurely.
If your washing machine’s drive belt has failed, you will need to replace it. You can do this yourself by following these simple steps:
- Unplug the washing machine from the power outlet.
- Remove the access panel to the interior of the washer. This is usually located on the back or side of the machine.
- Locate the drive belt and remove it from the pulleys.
- Install the new drive belt by threading it through the pulleys.
- Put the access panel back in place and screw it into place.
- Plug the washing machine back into the power outlet and turn it on.
9. Timer.
If your GE washer is not draining, the timer may be to blame. The timer controls all the washing machine’s functions, including the drain cycle.
If it’s defective, it may not advance properly to signal the drain pump to turn on. To determine if the timer is defective, consult your washer’s wiring diagram and use a multimeter to test it for continuity.
If the timer is defective, you’ll need to replace it. Fortunately, this is a relatively easy repair that you can do yourself. Simply unplug the washer, remove the back panel, and disconnect the wires from the old timer. Then, connect the wires to the new timer and reassemble the washer.
10. Water Level Control Knob.
This knob controls how much water is released into the washer during each cycle. If it is turned to the “off” position, no water will be released and your clothes will not get clean.
Why does it fail?
There are a few reasons why the water level control knob might fail. The most common reason is that the knob itself is faulty and needs to be replaced.
One reason could be that the water level control knob is not set to the correct position.
Another possibility is that there is a problem with the wiring or connections to the knob. Finally, it is also possible that the water level sensor itself is not working properly.
How to fix it?
If the water level control knob is not working properly, there are a few things that you can try to fix it.
First, make sure that the knob is set to the correct position. If it is not, adjust it and see if that fixes the problem.
Next, check the wiring and connections to the knob. If they are loose, tighten them up and see if that solves the problem.
Finally, if all else fails, you may need to replace the water level control knob. Fortunately, this is a relatively easy and inexpensive fix.
If you have checked the water level control knob and it is in the correct position, there are a few other things that could be causing your washer to not fill with water.
One possibility is that the inlet hose is kinked or clogged. The inlet hose is the hose that carries water into the washer. If this hose is kinked, water will not be able to flow into the washer.
Another possibility is that the water inlet valve is not working properly. The water inlet valve is what opens and closes to allow water to enter the washer. If this valve is not opening, water will not be able to get into the washer.
11. Lid Switch.
This is the most common reason why your GE washer won’t drain. The lid switch is a safety mechanism that prevents the washer from spinning when the lid is open.
If this switch is damaged or defective, it will prevent the washer from draining. To test the lid switch, open the lid and watch for the washer to stop draining. If the washer doesn’t stop, then the lid switch is likely defective.
Why does it fail?
There are a few reasons why your GE washer’s lid switch might fail. The most common reason is because the switch itself is worn out from years of use. Another possibility is that the wiring to the switch has become frayed or broken.
How to fix it?
If the lid switch itself is the problem, you’ll need to replace it. This is a relatively easy repair that you can do yourself. Simply order a new switch and follow the instructions in your owner’s manual to install it.
If the wiring is the problem, you’ll need to call an appliance repair technician to fix it. This is a more difficult repair and should only be attempted by someone with experience.
What are the consequences?
If your GE washer’s lid switch fails, the washer will not be able to start. This can be frustrating if you’re in the middle of doing laundry, but it’s not a huge problem. The biggest consequence is that your laundry will pile up until you can get the washer fixed.
12. Poor Load Distribution.
One of the most common problems that can cause a GE washer not to drain properly is poor load distribution.
When there is too much laundry in the washer, it can become unbalanced and cause the washer to shake excessively.
This can prevent the water from draining out of the washer properly. To fix this problem, simply redistribute the laundry in the washer so that it is evenly balanced.
Related:
GE Top Load Washer Not Draining Or Spinning?
If your GE top load washer is not draining or spinning, there are a few things you can do to try and fix the problem.
First, check to make sure that the washer is properly plugged into an outlet. Next, check the power cord for any frayed or damaged wires. If you find any damage, replace the power cord.
If the washer is still not draining or spinning, there may be an issue with the washing machine pump. The pump is responsible for moving water from the washer tub to the drain.
If the pump is clogged or damaged, it will need to be replaced. Finally, if all else fails, you may need to call a professional to service your washer.
GE Front Load Washer Not Draining Or Spinning?
If your GE front load washer is not draining or spinning, there are a few things you can check to try and fix the issue.
First, make sure that the washer is plugged in and that the power cord is not damaged. Next, check the door seal to make sure it is clean and free of any debris.
Finally, check the drain hose to make sure it is not kinked or blocked. If you have checked all of these things and the washer still will not drain or spin, you may need to call a repairman.
GE washer dryer combo not draining?
If your GE washer dryer combo is not draining, there are a few things you can do to troubleshoot and fix the problem.
First, check to make sure that the drain hose is not kinked or clogged. If it is, try straightening it out or clearing the obstruction.
Next, check the drain pump filter for any foreign objects that may be blocking it. If you find anything, remove it and clean the filter.
Finally, check the drain pump itself for any debris or obstructions. If you find anything, remove it and clean the pump.
If your GE washer dryer combo still will not drain after following these steps, then you may need to call a technician for assistance.
How do you force a GE washer to drain?
If your GE washing machine isn’t draining properly, there are a few things you can do to try and fix the problem. First, check the drain hose to make sure it’s not kinked or blocked. If that doesn’t solve the problem, you may need to clean out the drain pump filter.
To do this, unplug the washing machine and remove the lower access panel. Locate the drain pump filter (it will be a small round screen) and clean it out with a toothbrush or other small brush. Once you’ve done that, reassemble everything and try running the washer again.
How do I test my GE washing machine drain pump?
To test your washing machine’s drain pump, unplug the machine and remove the drain hose from the back. Place the end of the hose into a bucket and make sure that the bucket is big enough to catch all of the water that will be drained.
Turn on the washing machine and let it run for a few minutes. If the pump is working properly, you should see a steady stream of water flowing into the bucket. If the pump is not working properly, you may need to replace it.
If your washing machine does not have a drain hose, you can test the drain pump by removing the bottom panel of the machine. Locate the drain pump and make sure that it is not obstructed.
Turn on the machine and let it run for a few minutes. If the pump is working properly, you should see water flowing out of the drain pump. If the pump is not working properly, you may need to replace it.
Where is the drain filter on my GE washer?
The drain filter on your GE washer is located on the back of the machine, near the bottom. To access it, you will need to remove the back panel of the washer. O
nce you have removed the panel, you should see the drain filter attached to a hose. Simply detach the hose and remove the filter to clean it out. Be sure to reattach the hose and panel before using your washer again.
Does a GE top load washer have a filter?
Yes, a GE top load washer has a filter. The filter is located in the pump and is used to remove any lint or debris from the water before it enters the tub. It is important to clean the filter regularly to ensure optimal performance of your washer.
Where is the coin trap on a GE top-load washer?
The coin trap is located under the washer’s agitator. To access it, remove the agitator by unscrewing the retaining nut at the base of the agitator.
The coin trap is a small, cylindrical piece that fits over the end of the drain hose. If your washer is leaking water from the coin trap, clean it out and replace the O-ring seal.
If your washer is leaking water from somewhere else, check the door gasket and lid seal for cracks or tears. Replace the gasket or seal if necessary. If you can’t determine where the leak is coming from, call a repair technician.
How do you reset a GE washing machine?
If your GE washing machine is not working properly, you may need to reset it. To do this, simply unplug the machine from the power outlet and then plug it back in. You should then press and hold the “Start/Pause” button for five seconds. This will reset the machine and hopefully fix any issues you were having.
Related: 11 Types of Washing Machines: Which One Is Right for You?
Conclusion
If your GE washer is not draining, there are a few things you can do to troubleshoot and fix the issue. First, check the drain hose to make sure it is clear of any clogs or blockages. If the hose is clear, then check the pump for any debris or obstructions.
Finally, if neither of these solutions fix the problem, you may need to contact a professional for help. With a little troubleshooting, you should be able to get your GE washer draining properly again in no time!
If this article was helpful, please share it with others so they can benefit from it as well!
