Last Updated on September 21, 2022 by Jason Nguyen
If your Maytag washer isn’t draining, you’re not alone. This is a common problem that can be fixed with a few simple steps.
In this blog post, we will walk you through the process of fixing a Maytag washer that isn’t draining properly. We will provide step-by-step instructions on how to do it yourself, as well as tips and advice on how to prevent this problem from happening again. Let’s get started!
Related: 7 Washing Machine Brands To Avoid and 3 Most Reliable Brands
How to Fix a Maytag Washer Not Draining: Step-by-Step Instructions
1. Drain Hose
If your Maytag washer is not draining, there are a few things you can check yourself before calling a technician. First, make sure that the drain hose is not clogged. The drain hose is the flexible tube that connects the pump to the drainage port in your washing machine.
If this hose is clogged, it will prevent water from draining from the washer. To clean the drain hose, disconnect it from the washer and use a wire brush or plumbing snake to clear any debris that may be blocking it. Once the hose is clear, reattach it to the washer and try running a cycle again.
How to prevent it?
To prevent your Maytag washer from not draining in the future, be sure to clean the lint filter after every load of laundry. The lint filter is located on the front of the washer and can be accessed by opening the door.
Simply remove any lint or debris that has been collected in the filter and then close the door. You should also clean the inside of the washer tub on a monthly basis to prevent build-up.
Use a mild detergent and a soft cloth to wipe down the tub. Be sure to rinse it thoroughly before running another load of laundry.
2. Clogged Pump or Hose
If your Maytag washer is not draining, it could be because the pump or hose is clogged. To fix this, you will need to clean out the pump and/or hose.
Start by unplugging your washer from the power outlet. Next, locate the drain pump on your washer. The drain pump is usually located near the bottom of the washer. Once you have found the drain pump, remove the hose that is attached to it.
Once the hose is removed, check for any blockages in the pump. If there are any blockages, use a small brush or toothpick to remove them. Once you have cleared the blockages, reattach the hose to the pump and plug your washer back into the power outlet.
3. Gentle or delicate cycle or Low Spin speed selected
If you have your washer set to a Gentle or delicate cycle, or a Low Spin speed, it is normal for the washer to take longer to drain. This is because these settings are designed to protect your clothes and prevent them from being damaged during the washing process.
To ensure that your clothes are getting clean, you can try running a test cycle with a small load of laundry. If the washer can clean the clothes properly, then you know that the problem is not with the machine.
4. Drain Height
If your washer is not draining, it could be the result of the drain being installed at an improper height.
The drain for your washer should be no more than 36 inches from the floor, and no less than 30 inches. If it is installed outside of this range, it could cause your washer to not drain properly.
5. Detergent Quantities.
If you have a high-efficiency (HE) washer, you need to use less detergent than you would in a traditional top-loading washer. HE detergents are made for lower water volumes and can be more concentrated. Follow the manufacturer’s instructions on how much detergent to use.
If you’re using too much detergent, it can cause your washer to not drain properly. If you’re using too little detergent, your clothes may not come clean.
If you have a front-loading washer, the best way to measure detergent is by weight rather than volume. Use about one ounce of HE detergent per pound of laundry.
6. Poor Load Distribution
Your washer may not be draining properly because of poor load distribution. This means that there is an imbalance in the way your clothes are distributed in the washer. To fix this, simply redistribute your clothes evenly in the washer before starting the cycle.
If you have a top-loading washing machine, make sure that the clothes are not packed too tightly. Clothes that are too close together can prevent water from circulating properly, which will lead to poor cleaning and increased wear on your clothes.
7. Drain Pump
The drain pump on your Maytag washer forces water through the hose and into the spin tube. The pump can become clogged with lint or other debris, causing the washer not to drain. Cleaning the pump regularly will help keep your washer working properly.
To clean the drain pump:
-Unplug the washer and remove the drain hose from the pump.
-Remove any debris from the hose and pump.
-Rinse the pump with water and reinstall it.
-Reconnect the drain hose and plug in the washer.
8. Door Lock Motor and Switch Assembly
The door lock motor and switch assembly is located inside the washer near the door. The door lock motor turns a knob or lever to latch the door shut during the wash cycle. The switch activates the motor when the door is closed.
If your washer won’t start, doesn’t fill with water, can’t drain, or the door won’t close, the door lock motor and switch assembly might be to blame. You can check if the door lock motor is defective by opening and closing the door of your washer.
If you hear a clicking sound, then the motor is probably fine. However, if you don’t hear a clicking sound, then the door lock motor might be defective and will need to be replaced.
To replace the door lock motor and switch assembly:
-First, unplug your washer from the power outlet.
-Next, remove the screws that hold the control panel in place.
-Then, disconnect the wires from the door lock motor and switch assembly.
-Finally, replace the door lock motor and switch assembly with a new one and reassemble your washer.
9. Lid Switch Assembly
The lid switch assembly is located on the top of the washer near the lid. The function of this part is to keep the washer from spinning when the lid is open.
If your washer will not spin, but will agitate, then you may need to replace your lid switch assembly. This is a very easy repair that can be done by most homeowners.
To check if the lid switch assembly is the problem, open the lid and try to start the washer. If the washer does not start, then the lid switch assembly is likely defective.
You can test this by unplugging the washer and remove the two wires from the lid switch. Touch the two wires together and then plug the washer back in. If the washer starts, then the lid switch is defective and will need to be replaced.
Replacing the lid switch assembly is a very easy repair. You will need to unplug the washer and remove the top panel of the washer. There are usually four screws that hold the top panel in place.
Once the top panel is removed, you will be able to access the lid switch assembly. Two wires connect to the lid switch. Disconnect these two wires and then remove the screws that hold the lid switch in place. Install the new lid switch in the reverse order and then reassemble your washer.
10. Water Pump Belt
If your washer is not draining, it could be because the water pump belt has come off. The water pump belt is responsible for pumping the water out of the washer and into the drain hose. If the belt is not functioning properly, the water will not be able to drain from the washer.
To check if the water pump belt is the problem, first unplug the washer from the power outlet. Then, remove the access panel to the water pump.
The water pump is usually located near the bottom of the washer. Once you have removed the access panel, you will be able to see the water pump belt. If the belt is broken or damaged, it will need to be replaced.
11. Drain Pump Filter
If your Maytag washer is not draining, one possible reason is that the drain pump filter is clogged.
The drain pump filter is located under the washer tub, and it catches lint and other debris that can build up in the washer tub over time.
If the drain pump filter becomes clogged, it can cause the washer to not drain properly.
To clean the drain pump filter:
- Unplug the washer from the power outlet.
- Remove the screws that secure the washer tub to the washer cabinet, and then lift off the washer tub.
- Locate the drain pump filter under the washer tub. It is a small white cylindrical piece with a black cap.
- Unscrew the black cap from the drain pump filter, and then remove the filter screen from the housing.
- Rinse the filter screen under running water until it is clean.
- Replace the filter screen in the housing, and then screw on the black cap.
- Lower the washer tub into place, and then screw it back into the washer cabinet.
- Plug the washer back into the power outlet.
12. Coin Trap
The coin trap is a small, plastic cup-shaped piece located under the washer tub. It catches any small items that fall through the wash basket hole, such as coins or buttons.
If your Maytag washer isn’t draining properly, there’s a good chance that something is blocking the coin trap. To clean it out, follow these steps:
- Unplug the washer from the power outlet.
- Remove the lower front panel of the washer. This will give you access to the coin trap.
- Use a small, flat-head screwdriver to remove the coin trap cap. Be careful not to lose the spring that’s underneath it.
13. Door Lock
If your washer is not draining, one possible reason is that the door lock is defective. The door lock prevents the washer from draining while the door is open. If the door lock is defective, the washer will not drain.
To test the door lock, open the door and press and hold the start/pause button for five seconds. The door should lock and the washer should start draining. If the door does not lock, or if the washer does not start draining, replace the door lock.
14. Drive Belt
The drive belt is a long, narrow band that wraps around the outer edge of the washer tub. The other end of the drive belt is attached to the washer motor.
As the motor turns, it rotates a large pulley inside the washer. The drive belt is what transfers this motion from the motor to the pulley, and ultimately to the washer tub.
If your washer is not draining, one possible reason is that the drive belt has come off or broken. If this is the case, you will need to replace the drive belt.
Replacing a drive belt is a relatively simple repair that you can do yourself. Just be sure to unplug the washer from the power source before you begin.
Related:
- 14 Reasons Why Maytag Washer That’s Not Spinning: How To Fix
- How to Fix a Maytag Washer That Won’t Start
Maytag washer not draining on normal cycle?
There are a few things that could be causing this.
One possibility is that the washer isn’t level. If it isn’t level, the water won’t be able to drain properly. You can check to see if your washer is level by using a level. Place the level on top of your washer and see if it is level. If it isn’t, you will need to adjust the legs until it is level.
Another possibility is that the drain hose is clogged. The drain hose carries the water from the washer to the drain. If the hose is clogged, the water won’t be able to get through and will back up into the washer.
You can check to see if the hose is clogged by removing it from the washer and checking for any blockages. If you find a blockage, you will need to clear it before putting the hose back on.
If your washer is still not draining properly, there may be something wrong with the pump. The pump is responsible for pumping the water out of the washer. If the pump is damaged, it may not be able to properly pump the water out. You will need to have a technician take a look at your washer to determine if the pump needs to be replaced.
Related:
- 10 Reasons Why Kenmore Washer Not Draining: How to Fix
- 10 Reasons Why Hotpoint Washer Not Draining: How to Fix
- 8 Reasons Why Frigidaire Washer Not Draining: How to Fix It
- 11 Reasons Why LG Washer Not Draining and {How to Fix}
- GE Washer Not Draining: How to Troubleshoot and Fix
Maytag washer not draining fabric softener?
If your Maytag washer isn’t draining fabric softener, there are a few things that could be causing the problem. Here’s a look at some of the most common causes and how to fix them.
One possible reason for your Maytag washer not draining fabric softener is that the fabric softener dispenser is clogged. The dispenser can become clogged with fabric softener buildup, lint, or other debris. To clean the dispenser, simply remove it from the washer and rinse it out with warm water.
Another possible reason for your Maytag washer not draining fabric softener is that the fabric softener pump is damaged or defective. The fabric softener pump is responsible for pumping the fabric softener from the dispenser into the washer tub. If the pump is damaged or defective, it will need to be replaced.
If your Maytag washer is still not draining fabric softener after you’ve cleaned the dispenser and checked the pump, there may be an issue with the washer tub itself. If the washer tub is cracked or damaged, it will need to be replaced.
If you’re still having trouble with your Maytag washer not draining fabric softener, there are a few other things that you can try. First, make sure that the fabric softener dispenser is properly inserted into the washer. Next, check the fabric softener setting on your washer to make sure that it’s set to the correct amount. Finally, if you have an HE (high efficiency) washer, make sure that you’re using HE-compatible fabric softener.
Maytag washer not draining on spin cycle?
If your washer isn’t draining properly, it could be due to a few different reasons. Let’s take a look at some of the most common causes and how to fix them.
One of the most common reasons why your Maytag washer might not be draining properly is that the drain hose is clogged. If this is the case, you’ll need to clear the blockage to get your washer draining again. Another common reason for this problem is a bad pump. If your washer has a bad pump, it won’t be able to properly drain the water. You’ll need to replace the pump to fix this issue.
Maytag Neptune washer not draining?
This is a common problem that can have a few different causes. The good news is that it is usually an easy fix.
One common cause of a Maytag Neptune washer not draining properly is a clogged drain hose. The drain hose can become clogged with lint, hair, and other debris. To clean the drain hose, detach it from the washer and use a plumbers’ snake or a wire hanger to clear the clog.
Another common cause of a Maytag Neptune washer not draining properly is a faulty drain pump. The drain pump helps to circulate water and remove it from the washer tub. If the drain pump is defective, it will need to be replaced.
If your Maytag Neptune washer is not draining properly, check the drain hose and drain pump for clogs or defects. If you cannot fix the problem yourself, contact a qualified appliance repair technician for assistance.
Maytag centennial washer not draining?
There are a few things that could be causing this. The most common cause is a clogged drain hose. If your washer is not draining, check the drain hose for any blockages. If you find one, clear it and try again.
Another possible cause is a malfunctioning pump. If your washer’s pump is not working properly, it will not be able to drain the water. You can check the pump by opening up the washer and inspecting it. If you find that it is indeed the pump, you will need to replace it.
Lastly, a faulty lid switch could also be preventing your washer from draining properly. The lid switch is located under the washer’s lid and is responsible for telling the washer when to start and stop.
If the lid switch is not working properly, it will not allow the washer to drain. You can test the lid switch with a multimeter. If it is indeed the problem, you will need to replace it.
Maytag front load washer not draining?
There are a few things that could be causing the issue. Here are some potential causes and how to fix them.
One potential cause of a Maytag front load washer not draining properly is that the drain hose is clogged. The drain hose is located on the back of the washer and goes from the washer to the drain.
If the drain hose is clogged, it will need to be cleared. Another potential cause is that the pump is not working properly. The pump is located under the washer and pumps the water out of the washer. If the pump is not working, it will need to be replaced.
If your Maytag front load washer is not draining properly, there are a few things that you can do to try to fix the issue. First, check the drain hose to see if it is clogged. If it is clogged, clear it and see if that fixes the problem.
If the drain hose is not the issue, then check the pump. If the pump is not working, then it will need to be replaced. Maytag front load washers are durable and reliable, but they can have issues from time to time.
Maytag top load washer not draining completely?
There are a few things that could be causing this. First, check to see if the washer is properly plugged into the outlet. If it is, then the next thing to check is the drain hose. The drain hose might be clogged or blocked. To unclog or clear a blockage in the drain hose, use a plunger.
If the drain hose is clear, then the next thing to check is the pump. The pump might be damaged or broken. To replace the pump, follow these instructions. First, unplug the washer from the outlet.
Next, remove the back panel of the washer. Locate and disconnect the hoses from the pump. Remove the pump from the washer. Install the new pump in the washer and reconnect the hoses. Replace the back panel of the washer and plug it back into the outlet.
Maytag Atlantis washer not draining?
You’re not alone. Many people have this problem and it’s usually because of one of these three things:
The washer isn’t level: If your washer isn’t level, the water won’t be able to drain properly. Use a level to check if your washer is level front-to-back and side-to-side.
The drain hose is clogged: The drain hose can become clogged with lint, dirt and other debris. Use a brush or a vacuum cleaner attachment to clean out the drain hose.
The pump is damaged: If the pump is damaged, it won’t be able to properly pump the water out of the washer. You’ll need to replace the pump.
Conclusion
If your Maytag washer is not draining, there are a few things you can do to try and fix the problem. First, check the drain hose to make sure it is clear of any debris. If that doesn’t work, try running a cycle with just hot water to see if that clears the problem. If neither of those solutions work, you may need to call a repairman.
Whatever the problem is, with a little troubleshooting you should be able to get your Maytag washer draining properly again in no time.