Last Updated on September 14, 2022 by Kimberly Crawford
If your Whirlpool washer isn’t draining, don’t panic! There are a few things that you can do to try and fix the issue. In this blog post, we will discuss some common causes of this problem and what you can do to solve it. We will also provide some tips for preventing this from happening in the future. Don’t let your dirty laundry pile up – read on for help!
Related: 7 Washing Machine Brands To Avoid and 3 Most Reliable Brands
What to Do When Your Whirlpool Washing Machine Won’t Drain
1. Drain Pump.
If your washer is not draining, the first thing to check is the drain pump. The drain pump helps to remove water from the washer during the spin cycle.
If the drain pump is not working properly, it can cause the washer to not draining properly.
Why does it fail?
There are a few reasons why the drain pump may fail. One reason is that the pump may be clogged with lint or other debris. Another reason is that the pump may be worn out and needs to be replaced.
How to fix it:
If you think that the drain pump is the problem, there are a few things that you can do to try and fix it. First, you can try to clean out the pump by removing any debris that may be clogging it. You can also try to replace the pump if it is worn out.
2. Drain Pump Filter.
If your washer isn’t draining properly, there could be a blockage in the drain pump filter. The drain pump filter is located under the wash tub, near the bottom of the washer.
To clean it, first unplug your washer and then remove the lower panel on the back of the washer.
Next, locate and remove the drain pump filter. Clean it with a brush and warm, soapy water. Rinse the filter thoroughly and then put it back in place.
Finally, replace the lower panel on the washer and plug your washer back in.
3. Excess Sudsing.
If your Whirlpool washing machine isn’t draining properly, there could be a few different reasons why.
One potential cause is excess sudsing. Excess suds can prevent water from draining out of the machine properly, leading to standing water in the tub.
Why does it fail?
There are a few reasons why your washing machine might start sudsing up too much. One possibility is that you’re using too much detergent.
If you use more than the recommended amount of detergent, it can cause excess sudsing. Another possibility is that your washing machine isn’t draining properly, which can lead to soap buildup and sudsing.
How to fix it?
Fortunately, this is usually an easy problem to fix. Simply run the washer through a second rinse cycle with no detergent to remove the suds. If that doesn’t solve the problem, you may need to clean out your machine’s filters or pump.
4. Clogged Pump or Hose.
If your Whirlpool washer is not draining, it may be due to a clogged pump or hose.
Why does it fail?
The Whirlpool washing machine is equipped with a pump that circulates water through the hose and into the washer.
If the pump becomes clogged, it will not be able to circulate the water properly and the washer will not drain.
How to fix it:
You can clean the pump by removing it from the washer and using a brush to remove any debris that may be blocking it.
To clean the pump, follow these steps:
– Unplug the washer from the power outlet.
– Remove the drain hose from the back of the washer.
– Use a brush and warm, soapy water to clean the pump.
– Rinse the pump with clear water.
– Reattach the drain hose and plug the washer back into the power outlet.
5. Wrong Whirlpool Wash Cycle Selected.
If your Whirlpool washing machine doesn’t seem to be draining properly, there’s a chance that you’ve selected the wrong wash cycle.
Check your owner’s manual to see what the different cycles are for and make sure you’re using the one that best suits your needs.
6. Door Lock Motor and Switch Assembly.
The door lock motor and switch assembly is located behind the control panel on the washer. The door lock motor turns the locking mechanism when the washer door is closed. The door switch prevents the washer from spinning or agitating when the door is open.
If your Whirlpool washing machine won’t drain, one possible reason could be a problem with the door lock motor or switch assembly. Here’s how to check and replace these parts:
First, unplug the washing machine and remove the control panel. Next, locate the door lock motor and switch assembly behind the control panel.
To test the door lock motor, first disconnect the wires from the motor. Then, using a multimeter, test for continuity between the two terminals on the motor. If there is no continuity, the door lock motor will need to be replaced.
To test the door switch, first disconnect the wires from the switch. Then, using a multimeter, test for continuity between the two terminals on the switch. If there is no continuity, the door switch will need to be replaced.
Once you have replaced the door lock motor or switch assembly, reassemble the washing machine and test it to see if it is now draining properly. If the problem persists, you may need to call a qualified appliance repair technician.
7. Lid Switch Assembly.
If your washer doesn’t start, the lid switch assembly might be defective. The lid switch is a safety device that keeps the washer from spinning when the lid is open. If the lid switch is defective, the washer won’t spin.
To check whether the lid switch is defective, open and close the lid of your washer. If you hear a click, the lid switch is probably working. If you don’t hear a click, the lid switch might be defective.
8. Water Pump Belt.
The water pump belt keeps the pump impeller moving and is an important part of the washer’s drainage system.
If your washer isn’t draining properly, one possible cause is a broken or damaged water pump belt. Fortunately, this is a relatively easy problem to fix yourself. Just follow these simple steps:
First, unplug your washer and remove the front panel. You’ll need a screwdriver for this.
Once the front panel is off, you should be able to see the water pump. There will be a belt running from the motor to the pump pulley.
Carefully remove the old belt and replace it with a new one. Make sure the new belt is tight but not too tight.
Once the new belt is in place, reattach the front panel and plug your washer back in. Run a test cycle to make sure the problem is fixed.
9. Coin Trap.
The coin trap is a small plastic cup located near the bottom of your washer. Its purpose is to catch any small items that may fall out of your pockets, like coins.
Over time, the coin trap can become clogged with these items and cause your washer to not drain properly. To clean it out, simply remove the coin trap and empty it into the trash.
If your washer is still not draining properly after cleaning the coin trap, there may be a more serious issue that needs to be addressed by a professional.
10. Drain Hose.
The most common issue with a washer not draining is a clogged
The most common issue with a washer not draining is a clogged drain hose. The drain hose is the rubber or plastic tube that connects the pump to the house drains.
Over time, this hose can become clogged with lint, hair, and other debris. If the hose is clogged, the washer will not be able to pump the water out and it will appear as if it is not draining.
To clean the drain hose, start by unplugging the washer and removing the hose from the pump. Next, use a plunger to try and clear any debris that may be blocking the hose.
If the plunger does not work, you can try using a wire hanger to fish out any debris. Once the hose is clear, reattach it to the pump and plug in the washer. Your drain hose should now be clear and your washer should drain properly.
11. Door Lock.
If your Whirlpool washer doesn’t seem to be draining properly, one possible reason is that the door lock is defective.
The door lock is a safety feature that keeps the washer from operating if the door is open. If the door lock is defective, it may not allow the washer to start or it may cause the washer to stop mid-cycle.
If you’re having problems with your Whirlpool washer, check the door lock to see if it’s the source of the problem. If the door lock is defective, you’ll need to replace it. Fortunately, this is a relatively easy repair that you can do yourself.
To replace the door lock on your Whirlpool washer, you’ll need a Phillips screwdriver and a new door lock. You can purchase a replacement door lock from an appliance parts store or online.
First, locate the door lock on your washer. The door lock is located on the front of the washer, near the bottom. It’s a small, rectangular piece of plastic with two Phillips screws.
Remove the two screws that hold the door lock in place. Then, pull the door lock off of the washer.
Take your new door lock and insert it into the opening on the washer. Make sure that the tab on the door lock is properly aligned with the slot on the washer. Then, replace the two screws and tighten them securely.
Once you’ve replaced the door lock, try operating your washer again to see if it’s draining properly. If it is, then your repair is complete. If not, there may be another issue causing your washer not to drain properly.
12. Poor Load Distribution.
If your washer is not draining properly, it could be due to poor load distribution. This means that the clothes are not evenly distributed around the tub.
To fix this, simply redistribute the clothes and try again. If this does not work, then you may need to call a professional.
Related:
- 10 Reasons Why Hotpoint Washer Not Draining: How to Fix
- 8 Reasons Why Frigidaire Washer Not Draining: How to Fix It
- 11 Reasons Why LG Washer Not Draining and {How to Fix}
Whirlpool washer spinning but not draining?
There are a few things that could be causing this. The first thing you should check is the drain hose. If it is clogged, it will need to be cleared.
Another possible cause is the pump itself. If it is not working properly, it will need to be replaced. Lastly, make sure that the washing machine’s spin cycle is set correctly. If it is set too high, it can cause the machine to not drain properly.
Whirlpool washer not draining and making noise?
There are a few things that could be causing this. First, check to see if there is anything blocking the washer’s drain hose.
If there is, clear it out and try again. If that doesn’t work, then the issue may be with the washer’s pump. To clean the pump, remove it from the washer and disassemble it.
Clean any debris that may be caught in it and then reassemble the pump. If the pump is still not working, then it may need to be replaced.
Finally, if none of these solutions work, then the issue may be with the washer’s control board. If this is the case, then you will need to contact a qualified repair person to fix it.
Whirlpool washer not draining completely?
1. Drain hose or pump.
The drain hose is the rubber or plastic hose that connects the pump to the back of the washer. If this hose is kinked, damaged, or not connected properly, it could be causing your washer not to drain completely.
How to fix it
Check that the drain hose is not kinked and that it’s properly connected to both the pump and the back of the washer. If it is damaged, you’ll need to replace it.
2. Drain pump.
If your Whirlpool washing machine isn’t draining completely, the most likely culprit is the drain pump. This part is responsible for moving water out of the washer during the draining cycle.
If it’s damaged or not working properly, your washer will be unable to get rid of all the water, resulting in a pool of water at the bottom of the machine.
There are a few things you can do to check if the drain pump is the issue. First, make sure that there is nothing blocking the pump or the drainage hose. If there is, clear it out and try running a cycle again. If that doesn’t work, you may need to replace the drain pump.
3. Water level sensor.
The water level sensor monitors the water level in the washer tub and sends a signal to the control board.
If the sensor is defective, it may not send the correct signal to the control board or it may not work at all. This can cause the washer to fill with too much water or not enough water.
To check the water level sensor, first make sure that there is no debris or build-up on the sensor. If the sensor is clean, then check for continuity between the two terminals on the sensor. If there is no continuity, then the sensor will need to be replaced.
Whirlpool washer not draining during spin cycle?
This is a common problem that can be caused by a few different things. First, check to make sure that the drain hose is not kinked or clogged. If it is, straighten it out or clear the blockage and try again.
Another possible cause is that the pump isn’t working properly. You can check this by removing the drain hose and seeing if water is being pumped out. If not, the pump will need to be replaced.
Finally, the issue could be with the spinning basket itself. If it is damaged or warped, it won’t spin properly and won’t drain the water. In this case, you’ll need to replace the basket.
Old Whirlpool washer not draining?
This is a common problem. There are several potential causes, but luckily there are also several potential solutions.
One potential cause of your old Whirlpool washer not draining properly could be a clogged drain hose. This hose can become clogged with lint or other debris over time. To clean your drain hose, disconnect it from the washer and flush it out with a garden hose. If your drain hose is clear and the washer is still not draining, the problem may be with the pump.
The first step in troubleshooting a non-draining washer is to check the drain hose for clogs. If the hose is clear, move on to checking the pump. The pump may be clogged with lint or other debris. To clean the pump, disconnect it from the washer and flush it out with a garden hose. If your pump is clear and the washer is still not draining, the problem may be with the drain pipe.
The drain pipe can become clogged with lint or other debris over time. To clean the drain pipe, disconnect it from the washer and flush it out with a garden hose. If your drain pipe is clear and the washer is still not draining, the problem may be with the washing machine itself.
If you have checked all of these potential causes and your old Whirlpool washer still will not drain, it is likely that the problem lies with the washing machine itself. In this case, you may need to call a repairman to take a look at your washer. However, there are some things that you can try before calling a repairman.
First, check the settings on your washing machine. Make sure that the setting for water level is set to “low” or “auto.” If it is set to “high,” this could be the cause of your problem. Also, make sure that the spin cycle is set to “off.” If it is set to “on,” this could also be causing your washer not to drain properly.
Related:
- How to Fix a Whirlpool Washer Door Locked Light Flashing
- 20 Reasons Why Whirlpool Washer Not Spinning? {How To Fix}
How to drain water from Whirlpool top load washing machine.
If your Whirlpool top load washing machine won’t drain, there are a few things you can try to fix the problem.
First, check to make sure that the drain hose is not kinked or clogged. If it is, straighten it out or remove the blockage.
Next, check the drain pump filter for any debris that may be blocking it. If you find anything, clean it out and try again.
Finally, if all else fails, you may need to call a service technician to come take a look at your washing machine.
Conclusion
If your Whirlpool washer isn’t draining, there are a few things you can try to fix the problem. First, check the drain hose to make sure it’s not clogged. If it is, clear it and try again. If that doesn’t work, you may need to replace the drain pump.
Thankfully, this is a relatively easy repair that you can do yourself. With a little time and effort, you can get your washer draining properly again.