20 Reasons Why Whirlpool Washer Not Spinning? {How To Fix}

Last Updated on August 22, 2022 by Kimberly Crawford

If your Whirlpool washer isn’t spinning, don’t worry – you’re not alone. This is a common problem that many people experience with their washers. In this blog post, we will discuss 10 ways to fix a whirlpool washer that’s not spinning. Hopefully one of these methods will help get your washer up and running again!

Related: 7 Washing Machine Brands To Avoid and 3 Most Reliable Brands

10 Ways to Fix a Whirlpool Washer That’s Not Spinning

1. Unbalanced or Jammed Load.

If your washer is overloaded, it will spin more slowly to avoid damaging the machine. To speed up the spin cycle, redistribute the load evenly around the wash basket.

If clothing is jammed around the perimeter of the wash basket, remove it and try spinning again.

2. Level the Washer.

The first thing you want to do is make sure the washer is level. An unlevel washer can cause all sorts of problems, chief among them being a washer that doesn’t spin.

You can check this by opening the door and looking at the underside of the washer. There should be four leveling feet, two in the front and two in the back. If these are not level, the washer will not spin properly.

3. Washer is Overloaded.

The most common cause of a washer not spinning is that it’s overloaded. To fix this, simply remove some of the clothes from the washer and try again.

If your washer still doesn’t spin, then there may be something else wrong with it. Continue reading to learn more about other possible causes and how to fix them.

4. Reset the Washer.

If your washer isn’t spinning, the first thing you should do is reset it. To do this, simply unplug the washer for 30 seconds and then plug it back in. This will often fix the problem and get your washer spinning again.

5. Drain Hose.

The next thing you want to check is the drain hose. If there is a kink in the hose, it could be preventing water from draining properly.

Why does it fail?

There are several reasons why a drain hose might fail. The most common reason is a kink in the hose. This can prevent water from draining properly, and cause the washer to stop spinning.

Another reason might be a clog in the hose. This can also prevent water from draining properly and cause the washer to stop spinning. Finally, the drain hose might be too long. If it is too long, it can prevent water from draining properly and cause the washer to stop spinning.

How to fix it?

Inspect the hose for any damage and make sure it is not bent or crimped. If everything looks good, try running water through the hose to see if that clears the problem. If not, you may need to replace the hose.

To replace the hose:

First, disconnect the old hose from the washer. There should be a clamp holding it in place. Loosen the clamp and remove the hose.

Next, take the new hose and connect it to the washer, making sure to secure it with the clamp. Once everything is tight, turn on the water and try running a cycle.

How to prevent it?

To prevent this from happening again, make sure to check the hose regularly for any kinks or damage. Also, be careful not to bend or crimp the hose when moving the washer.

6. Drain pump.

Another thing to check is the drain pump. The drain pump helps to remove water from the washer during the draining cycle. If the pump is damaged, it could prevent the washer from draining properly.

How to fix it?

Inspect the pump for any damage and make sure it is not blocked by anything. If everything looks good, try resetting the washer. If that doesn’t work, you may need to replace the drain pump.

To replace the drain pump:

-Disconnect the power to the washer.

-Remove the back panel of the washer.

-Remove the hoses from the old pump and connect them to the new one.

-Attach the new pump to the washer and reconnect the power.

How to prevent it?

To prevent this problem from happening, make sure to regularly clean out the drain pump. You can do this by unplugging the washer and removing the pump.

Clean any debris or dirt that may be blocking the pump and then replace it. Doing this will help to keep your washer working properly for a longer period of time.

7. Drain Valve.

The first thing you want to check is the Drain Valve. If the washer is not draining, it will not spin. Check to make sure that the Drain Valve is open and not clogged.

If the valve is clogged, you will need to clean it out. You can use a toothbrush or a small brush to clean the valve.

8. Door Lock.

The door lock is an important safety feature on your washer. If the door lock is defective, the washer will not spin.

Why does it fail?

The door lock can fail due to a power surge, wear and tear, or a manufacturing defect.

How do you know it’s the door lock? If the washer is not spinning, but the motor is running, it is likely that the door lock is defective.

What are the symptoms?

The most common symptom of a defective door lock is the washer not spinning.

To check if the door lock is defective, first make sure that the washer is in standby mode. The washer should be turned off and all indicator lights should be off. If the door lock is defective, the door will not latch shut.

If the door lock is defective, replace it.

To replace the door lock:

-Remove the screws that secure the door lock.

-Remove the door lock.

-Install the new door lock.

-Secure the new door lock with screws.

How to prevent it?

To prevent the door lock from failing, do not overload the washer. Overloading the washer can cause a power surge that can damage the door lock. Also, do not use harsh chemicals to clean the door lock. Harsh chemicals can damage the door lock and cause it to fail.

9. Drain Pump Filter.

The drain pump filter is located on the front of your Whirlpool washer.

Why does it fail?

Lint and other debris can accumulate in the drain pump filter, causing it to fail.

How do I fix it?

Clean the filter by removing it and using a brush to remove any debris. You can also try using a vacuum cleaner with the hose attachment to remove any debris.

How to prevent it?

Clean the filter regularly to prevent lint and other debris from accumulating. You should also check the hoses for any blockages.

10. Lid Switch.

The lid switch is a safety device located under the washer’s lid. When the lid is closed, it activates the washer’s spinning cycle. If the lid switch is defective, the washer will not spin.

Why does it fail?

Lid switches can fail due to normal wear and tear. They can also be damaged by objects falling into the washer or by excessive vibration during the spin cycle.

How do you fix it?

To check if the lid switch is defective, open and close the washer’s lid several times. If you hear a clicking noise, the switch is probably working. If you don’t hear a click, the switch may be defective.

You can test the switch with a multimeter. First, unplug the washer and remove the lid. Locate the two wires that connect to the switch and disconnect them.

Set your multimeter to Ohms and touch the probes to the two terminals on the switch. If the reading is infinity, the switch is open and needs to be replaced. If the reading is zero, the switch is closed and working properly.

If the lid switch is defective, you’ll need to replace it. This is a relatively easy repair that can be done without calling a technician.

How to prevent it?

Be careful not to overload the washer and don’t allow objects to fall into it. Excessive vibration can also damage the lid switch, so make sure the washer is level and doesn’t rock back and forth during the spin cycle.

11. Drive Belt.

The drive belt is a rubber belt that goes around the drum and connects to the motor. If the drive belt is broken, the washer will not spin.

Why does it fail?

The drive belt can fail because it is old and worn out, or because it has come loose from the drum. If the drive belt is broken, the washer will not spin.

How to fix it:

If the drive belt is old and worn out, you will need to replace it. If the drive belt has come loose from the drum, you will need to reattach it.

How to prevent it?

You can prevent the drive belt from failing by regularly checking it for wear and tear, and replacing it if necessary. You can also prevent the drive belt from coming loose by making sure that all of the screws on the washer are tightened securely.

12. Drive Pulley.

The drive pulley is what the washer’s belt attaches to. If the drive pulley is not spinning, then the washer will not spin.

Why does it fail?

The drive pulley can fail for a few reasons. The most common reason is that the bearings in the pulley are worn out.

How to fix it

You will need to replace the drive pulley. This is a fairly easy repair that you can do yourself. You can find the drive pulley at your local hardware store or online.

To replace the drive pulley:

  • Unplug the washer from the power outlet.
  • Remove the washer’s cabinet.
  • Remove the old drive pulley.
  • Install the new drive pulley.
  • Reassemble the washer’s cabinet.
  • Plug the washer back in to the power outlet.

How to prevent it?

You can prevent this problem by regularly cleaning your washer. This will help to remove any build-up of dirt and grime that can cause the pulley to fail.

You should also check the pulley for any signs of wear and tear. If you see any, then you should replace it before it fails.

13. Drain Pump.

The Drain Pump helps expel water from the washer during the draining cycle.

How to fix it:

You can try to clean the Drain Pump by removing any debris that may be clogging it. If that doesn’t work, you’ll need to replace the Drain Pump.

To replace the Drain Pump:

  • Unplug the washer from the power outlet.
  • Remove the screws that hold the back panel in place.
  • Disconnect the hoses from the pump by pushing on the retaining tabs and pulling off the hoses.
  • Pull out the old pump and disconnect the electrical harness.
  • Install the new pump by reversing the above steps.
  • Plug in the washer and test it to make sure it’s draining properly.

How to prevent it?

Keep the washer clean and free of debris. Check the hoses regularly for any blockages.

14. Motor Coupling.

The motor coupling connects the inner wash tub to the transmission. If the washer is not spinning, but you can hear the motor running then this part may be defective. This part is located between the inner wash tub and the transmission.

Why does it fail?

Over time, the motor coupling can become worn out from use. If the washer is overloaded, this part can break.

How to fix it:

To check if this part is defective: With the washer turned off, disconnect power from the washer.

Remove the back panel of the washer. Inspect the motor coupling for signs of wear or damage. If the motor coupling is damaged, it will need to be replaced.

How to prevent it?

To prevent this part from failing, do not overload the washer. Be sure to follow the manufacturer’s recommendations for the maximum load capacity of your model washer.

Regularly inspect this part for signs of wear and damage. If you notice any damage, replace this part before it fails.

15. Clutch.

About this part: The clutch is located between the inner tub and the transmission. It is a large, round, black plastic part with metal teeth on the inside.

Why does it fail?

The clutch can fail for a few reasons. The most common is that the metal teeth on the inside of the clutch wear down over time and eventually break.

This can happen if the washer is overloaded or if there is something caught in between the tub and the basket, preventing it from spinning freely.

Another reason the clutch can fail is because the plastic housing that holds the metal teeth breaks. This can happen if the washer is dropped or jarred, or if something heavy is dropped on it.

Finally, the clutch can fail because the bearings that support it wear out. This is most likely to happen if the washer is used frequently or for very large loads.

How to fix it?

If the clutch is worn out, it will need to be replaced. This is a difficult repair that should be done by a professional.

If the plastic housing is broken, it can sometimes be glued back together. However, this is not a very strong repair and it is likely that the housing will break again. In this case, it is best to replace the entire clutch assembly.

If the bearings are worn out, they will need to be replaced. This is also a difficult repair that should be done by a professional.

How to prevent it?

There are a few things you can do to prevent the clutch from failing. First, make sure you never overload the washer. Second, keep the area around the washer clean and free of debris.

Finally, if you notice that the washer is not spinning as freely as it should, have a professional check it out to see if the clutch needs to be replaced.

16. Rotor.

The rotor is what actually spins the tub and contains a small, unbalanced weight on the end. If your washer isn’t spinning, it could be that the rotor is damaged or worn out.

Why does it fail?

Over time, the rotor can become damaged or worn out from all the spinning. This usually happens gradually and you may not notice it until your washer isn’t spinning properly.

How to fix it?

There are a few things you can do to try to fix a damaged or worn out rotor. First, you can try to replace the unbalanced weight on the end of the rotor.

This is a relatively inexpensive and easy fix that you can do yourself. If this doesn’t work, you may need to replace the entire rotor. This is a more expensive and difficult fix, so you may want to hire a professional to do it for you.

How to prevent it?

There’s not much you can do to prevent a rotor from becoming damaged or worn out. Just be sure to follow the manufacturer’s instructions for care and maintenance of your washer. This will help extend the life of the rotor and other parts of your washer.

17. Stator Assembly.

The stator assembly is located in the washer tub. The stator assembly contains the drive motor and transmission. The stator assembly also houses the brake and clutch assemblies.

Why does it fail?

The stator assembly can fail due to a variety of reasons. The most common cause of failure is due to a build-up of lint and other debris in the stator assembly. This can cause the stator assembly to overheat and eventually fail.

How do you fix it?

To fix this problem, you will need to replace the stator assembly. You can purchase a new stator assembly from your local appliance store or online.

How to prevent it?

To prevent this problem from happening, you should regularly clean your washer. You should also check the stator assembly for any build-up of lint or other debris. If you find any build-up, you should remove it immediately.

18. Drive Motor.

The drive motor is located beneath the washer tub, mounted to the bottom of the cabinet. The drive motor uses a small plastic gear to engage with a large metal gear attached to the washtub. Over time, these gears can wear out or strip, causing the washer not to spin.

How to fix it?

If the drive motor is not working, you will need to replace it. This is a fairly easy repair that you can do yourself.

To replace the drive motor, you will need to:

  • Disconnect the power to the washer.
  • Remove the screws that hold the back panel in place.
  • detach the wires from the old motor and remove it.
  • install the new motor and reattach the wires.
  • replace the back panel and screw it in place.
  • reconnect the power to the washer.

19. Motor Control Board.

The motor control board is the “brains” of the washing machine. It controls how much water is let in, when the tub should fill and drain, and how fast the basket should spin.

If this part goes bad, it can cause your washer to not fill properly, not spin, or not drain.

Why does it fail?

Over time, the motor control board can develop cracks or break completely. This is usually caused by a power surge or another electrical issue.

How to fix it:

If your washing machine’s motor control board has failed, you will need to replace it. This is a fairly difficult repair and should only be attempted by someone with experience working with washing machines.

How to prevent it?

There are a few things you can do to help prevent your washing machine’s motor control board from failing. First, make sure to never overload your washing machine.

Second, try to avoid using too much detergent, as this can cause the motor control board to overheat. Finally, if you have an older washing machine, consider having it professionally serviced to ensure that it is running properly.

20. Transmission.

The transmission is a complex mechanism that has many moving parts. If any of these parts are worn out or not functioning properly, the washer will not spin.

The most common cause of a transmission failure is a broken drive shaft. Other causes can include a failed clutch, damaged gears, or a faulty torque converter.

How to fix it?

If your washer is not spinning, the first thing you should check is the transmission. To do this, you will need to open up the washer and inspect the transmission for any damage.

If you find any damaged parts, you will need to replace them. You can find replacement parts at most appliance stores or online. Once you have replaced the damaged parts, your washer should be able to spin again.

How to prevent it?

There are a few things you can do to prevent transmission problems in your whirlpool washer. First, make sure to keep the washer clean and free of any dirt or debris.

Second, be sure to lubricate the transmission regularly. Third, if you notice any strange noises coming from the washer, be sure to have it checked out by a professional.

Related:

Why Whirlpool top load washer not spinning clothes dry?

whirlpool top load washer not spinning clothes dry

There could be various reasons as to why your Whirlpool top load washer is not spinning clothes dry. It could be due to an issue with the washing machine itself, or it could be caused by something blocking the washer’s spinning mechanism. Here are some potential causes and solutions for this problem:

  • Check to see if there is anything blocking the washer’s spinning mechanism. If there is, clear it away and see if that fixes the problem.
  • Make sure that the clothes you’re trying to dry are not too heavy or bulky. This could cause the washer to struggle when trying to spin them dry.
  • Inspect the washing machine for any signs of damage. If there are any damaged parts, it’s likely that this is causing the problem.
  • Check the washing machine’s manual for troubleshooting tips. This could help you identify the cause of the problem and find a solution.

Why Whirlpool washer not spinning fast?

There could be a few reasons why your Whirlpool washer is not spinning fast. One reason could be that the lid switch is dirty or damaged. Another reason could be that the drive belt is loose or broken. Lastly, the spin cycle could be set to a lower speed.

Whirlpool cabrio washer not spinning water out of clothes?

whirlpool cabrio washer not spinning water out of clothes

If your Whirlpool cabrio washer isn’t spinning water out of clothes, the first thing you should do is check if the washer is level. If it’s not, then it needs to be adjusted so that it is.

The next thing you should check is whether the load is unbalanced. To do this, open up the washer and redistribute the clothes evenly. Finally, make sure that there’s nothing blocking the pump. If there is, then remove it and try again.

If none of these solutions work, then it’s likely that there’s something wrong with the washing machine itself and you’ll need to call a repairman.

Related: Washing Machine Water Usage: How Much Does a Washing Machine Use?

Whirlpool washer not spinning and making loud noise?

If your Whirlpool washer is not spinning and making a loud noise, there are several possible causes. The most common cause is an unbalanced load. If your washer is overloaded or imbalanced, it will make a loud noise and may not spin correctly. To fix this, simply redistribute the load evenly and try again.

Another possible cause is a clogged drain hose. If your washer’s drain hose is clogged, it can cause the washer to make a loud noise and not spin correctly. To fix this, simply clear the blockage from the hose and try again.

If your Whirlpool washer is still not spinning and making a loud noise, there may be an issue with the washer itself. If this is the case, it is best to contact a professional for help.

Whirlpool washer not spinning or agitating?

Here are some potential causes and solutions for this problem.

If your Whirlpool washer is not spinning or agitating, there are a few potential causes that could be the culprit. One possibility is that the lid switch is defective. Another possibility is that the drive belt is broken. Finally, the motor could be damaged.

To fix a defective lid switch, you will need to replace it. To fix a broken drive belt, you will need to replace it. And to fix a damaged motor, you will need to replace it.

How do I reset my Whirlpool washer that won’t spin?

If your Whirlpool washer does not spin, there are a few things you can try to reset it.

First, unplug the washer from the power outlet and wait 30 seconds.

Next, plug the washer back in and press the “Start/Reset” button. If this does not work, you will need to open the lid and manually reset the washer. To do this, locate the “Reset” button on the control panel and press it for three seconds.

Once the washer has been reset, you should be able to start it by pressing the “Start/Reset” button again. If your Whirlpool washer still does not spin, you may need to call a service technician to diagnose and repair the problem.

Conclusion

If your Whirlpool washer is not spinning, there are a few things you can do to try to fix the issue. First, check to make sure that there is nothing blocking the washer from spinning. Next, check the settings to make sure that the washer is set to spin. Finally, if neither of these fixes work, you may need to call a repairman.

We hope this blog post was helpful in troubleshooting your Whirlpool washer! If you have any other questions or concerns, feel free to reach out to us.