Last Updated on August 23, 2022 by Kimberly Crawford
If your Whirlpool washer’s door locked light is flashing, don’t worry – you’re not alone! This is a common problem that can be fixed relatively easily.
In this blog post, we will walk you through the steps to take to fix the issue. Keep in mind that these instructions may vary depending on the model of your washer. So, please consult your owner’s manual if you are unsure about anything. Let’s get started!
Related: 7 Washing Machine Brands To Avoid and 3 Most Reliable Brands
Reasons Why Whirlpool Washer Door Locked Light Flashing
1. Lid Switch And Striker.
The lid switch is usually found on the top of the washer near the lid. The striker is a small metal piece that protrudes from the washing machine cabinet and makes contact with the lid switch.
If your Whirlpool washer’s door locked light is flashing, it could be due to one of two reasons. The first is that the lid switch is not working properly. The second is that the striker is out of alignment.
Why does it fail?
Wear and tear is the most common reason for these parts to fail. Over time, the striker can become bent or damaged, preventing it from making contact with the lid switch.
The lid switch can also become worn down, preventing it from making a good connection with the striker.
How to fix it?
To check if the lid switch is the problem, open the washer’s lid and look for a small button near the top of the cabinet.
If this button is depressed, it means that the lid switch is engaged and the washer should start. If the button is not depressed, it means that the lid switch is not working and needs to be replaced.
To check if the striker is the problem, open the washer’s door and look for a small metal piece protruding from the cabinet. This is the striker. It should line up perfectly with the hole in the door. If it does not, then the striker needs to be adjusted.
How to prevent it?
There is not much you can do to prevent wear and tear on these parts. However, you can try to keep your washer as clean as possible. This will help to reduce the amount of dirt and grime that can build up on the parts and cause them to fail.
You should also check the alignment of the striker periodically to make sure it has not become misaligned.
2. Door switch.
The door switch is a small plastic piece that sits behind the washer’s control panel. When you push the start button, the switch closes and signals the washer to start.
If the door switch is defective, it won’t close properly, and your washing machine won’t start.
Why does it fail?
Door switches can fail either mechanically or electrically. A mechanical failure means the switch is physically damaged and won’t close properly. An electrical failure means there’s a problem with the switch’s circuit board.
How do you fix it?
To check if the door switch is defective, open the washing machine door and look for a small plastic piece that sits behind the control panel.
If you see that the switch is not closed properly, then it is most likely defective and will need to be replaced.
If the door switch is mechanically damaged, you’ll need to replace it. If the door switch is electrically damaged, you’ll need to replace the entire control panel.
You can find door switches and control panels at your local appliance store or online. Be sure to purchase a compatible part for your washing machine model.
How to prevent it?
To prevent the door switch from failing, make sure to regularly clean your washing machine’s control panel.
Wipe away any dirt or debris that might build up and prevent the switch from closing properly. You should also avoid overloading your washing machine, as this can put stress on the door switch and cause it to fail.
3. Door Latch.
If your washer’s door is locked and the “locked” light is flashing, it usually means that there is an issue with the door latch. The most common cause of this problem is a faulty door switch.
Why does it fail?
Door switches can fail either mechanically or electrically. A mechanical failure means that the switch is physically damaged and will need to be replaced. An electrical failure means that there is a problem with the wiring or connection to the switch.
How do I fix it?
If you have a mechanical failure, you will need to replace the door switch. If you have an electrical failure, you will need to check the wiring and connections to the door switch.
To replace the door switch:
-First, you will need to identify the faulty door switch. You can do this by testing the continuity of the switch with a multimeter.
-Next, you will need to remove the screws that hold the door switch in place.
-Once the door switch is removed, you can install the new one by following the same process in reverse.
-Finally, you will need to test the new switch to make sure it is working properly.
If you have an electrical failure:
-First, you will need to check the wiring between the door switch and the control panel. Make sure that there are no loose connections or damaged wires.
-Next, you will need to check the door switch itself. Make sure that it is properly connected to the control panel.
-If everything looks okay, you may need to replace the door switch.
-Finally, you will need to test the new switch to make sure it is working properly.
How to prevent it?
There are a few things you can do to prevent this problem from happening:
-Regularly check the door switch for signs of wear and tear.
-Be careful not to damage the door switch when cleaning the washer.
-Make sure that the wiring between the door switch and the control panel is secure and in good condition.
4. Actuator Motor.
The actuator motor is located on the back of the washer, near the bottom. It’s a small black box with a white wire coming out of it.
The other end of the white wire goes to the door lock switch. When you push the button to start the washer, the actuator motor turns on and off to open and close the door lock.
If the actuator motor is defective, the washer will not start. The door locked light will flash and you’ll hear a clicking noise from the back of the washer.
Why does it fail?
There are several reasons why the actuator motor might fail. The most common reason is that the door lock switch is defective.
If the switch is bad, it won’t send power to the actuator motor. Another possible reason is that the wires going to the actuator motor are loose or damaged. Finally, the actuator motor itself could be defective.
How to fix it?
To fix this, you’ll need to replace the actuator motor. Here’s how:
First, unplug the washer from the power outlet. Then, remove the two screws that hold the actuator motor in place.
Next, disconnect the white wire from the door lock switch. Finally, install the new actuator motor and screw it in place. Reconnect the white wire to the door lock switch and plug the washer back in.
How to prevent it?
There’s not much you can do to prevent this problem. Actuator motors are pretty reliable, so it’s not something that you need to worry about too much.
Just be sure to keep an eye on the door lock switch and make sure that the wires going to the actuator motor are in good condition.
5. Sensor Actuator.
The sensor actuator is located on the door lock assembly. It is a small plastic piece that extends and retracts when the door is locked or unlocked.
The most common reason the door locked light flashes on a Whirlpool washer is because the sensor actuator is not working correctly.
Why does it fail?
The sensor actuator can fail for a few reasons:
-The plastic tab on the actuator breaks
-Something is blocking the path of the actuator
-The door lock assembly is faulty
How to fix it?
If the door locked light is flashing, first check the sensor actuator for any obvious damage. If the plastic tab is broken, you will need to replace the entire door lock assembly.
If something is blocking the path of the actuator, simply remove the obstruction and test the washer again. If the door lock assembly appears to be faulty, you will need to replace it.
6. Drain Pump.
If the washer door is locked and the door lock light is flashing, it could be that the drain pump has failed.
The drain pump helps to expel water from the washer during the draining cycle. If it’s not working properly, water can back up into the washer, causing the door to lock.
Why does it fail?
Drain pumps can fail for a number of reasons. A common cause is a blockage in the pump, which can be caused by things like lint or dirt buildup. Another possibility is that the pump itself has become damaged or worn out.
How to fix it?
To fix this problem, you’ll need to replace the drain pump. Here’s how:
First, unplug the washer from the power outlet. Then, remove the screws that hold the back panel in place. With the back panel removed, you should be able to see the drain pump. Disconnect the hoses from the pump and then remove the pump from the washer.
To install the new pump, simply reverse the process. First, connect the hoses to the new pump. Then, place the pump back into the washer and secure it with screws. Finally, replace the back panel and plug the washer back into the power outlet.
How to prevent it?
You can help prevent this problem by regularly cleaning the washer’s drain pump filter. Consult your owner’s manual for instructions on how to do this. You should also avoid overloading the washer, as this can put strain on the drain pump and cause it to fail prematurely.
7. Hose.
About this part: The hose might be kinked, blocking the washer from draining.
Check the drain hose for any kinks or blockages. If you find one, straighten it out or remove the blockage so that water can flow freely through it.
8. Control Board.
This is the control board for your washer. It is what controls all the functions of your washer.
If your washer’s door locked light is flashing, it could be a sign that your control board is failing. This can happen if there is a problem with the wiring, or if the control board itself is faulty.
Why does it fail?
There are a few reasons. It could be because of a power surge, or because the control board is overheating.
How to fix it?
If your washer’s door locked light is flashing, you’ll need to replace the control board. This is a job for a qualified appliance technician. They will be able to diagnose the problem and replace the control board for you.
9. Water Supply.
If your Whirlpool washer’s door locked light is flashing, it could be because the water supply to the washing machine is not turned on. Check to make sure that the water valves behind the washing machine are turned on.
If they are, and the door locked light is still flashing, there may be a problem with the water inlet valve. This valve is located on the back of the washing machine and controls the flow of water into the tub. If this valve is defective, it will need to be replaced.
10. Water in the machine.
If your Whirlpool washer door locked light is flashing, it means that there is water in the machine. This can be caused by a few different things, so it’s important to troubleshoot the issue to determine the cause.
One possible cause of water in the machine is a clogged drain hose. If the drain hose is clogged, water will build up in the machine and eventually cause the door locked light to flash.
To fix this, simply unplug the machine and remove the drain hose from the back of the washer. Clear any blockages from the hose and then reattach it.
Another possible cause of water in the machine is a defective door seal. If the door seal is damaged, water can leak into the washer and cause the door locked light to flash. To fix this, simply unplug the machine and remove the door seal. Inspect the seal for any damage and replace it if necessary.
Related: 20 Reasons Why Whirlpool Washer Not Spinning? {How To Fix}
Whirlpool washer front load door locked light flashing?
Here are some possible causes and solutions:
-The washer’s door latch may be damaged or defective. Inspect the door latch for any damage and replace it if necessary.
-There may be something blocking the washer’s door from closing properly. Remove any objects that may be blocking the door and try closing it again.
-The washer’s door may be misaligned. Try adjusting the door and see if that fixes the issue.
-There could be a problem with the washer’s control panel. If the door locked light is flashing, it could indicate an error code.
Whirlpool top load washer door locked light flashing?
There are a few things that could be causing this. Let’s take a look at some of the most common causes and solutions.
One of the most common causes of the Whirlpool top load washer door locked light flashing is a faulty lid switch. If your lid switch is not working properly, it will cause the door locked light to flash. The best way to test your lid switch is to open the door and see if the light turns off. If it does, then you know that the switch is working properly.
Another common cause of the Whirlpool top load washer door locked light flashing is a clogged drain pump. If your drain pump is clogged, it will cause the water to not drain properly from the washer.
This will cause the door locked light to flash. The best way to test your drain pump is to unplug the washer and remove the hose from the back of the washer. Turn on the washer and see if water comes out of the hose. If it does, then you know that the pump is working properly.
If your Whirlpool top load washer door locked light is flashing and you have checked both of these things, then it is most likely an issue with the washing machine itself. The best thing to do in this situation is to call a technician and have them come out and take a look at it. They will be able to diagnose the problem and get your washer up and running again in no time.
Whirlpool duet washer door locked light flashing?
Here are some possible causes and solutions.
One possible cause of the Whirlpool duet washer door locked light flashing is that the door lock switch is defective. The door lock switch is a safety feature that keeps the washer from operating when the door is open.
If the door lock switch is defective, it may not allow the washer to operate even when the door is closed. To test the door lock switch, open the washer door and press and hold the door locked button for five seconds. If the light does not come on, then the door lock switch is defective and will need to be replaced.
Another possible cause of the Whirlpool duet washer door locked light flashing is that the washer is not getting enough power. Make sure that the washer is plugged into a working outlet and that the circuit breaker is not tripped. If the washer still does not have power, then there may be a problem with the wiring or the fuse box.
If the Whirlpool duet washer door locked light is flashing and the washer will not start, then there may be a problem with the door lock assembly. The door lock assembly consists of the door switch, the latch, and the strike. If any of these parts are damaged or defective, then the washer will not start. To replace the door lock assembly, follow the instructions in the owner’s manual.
If the Whirlpool duet washer door locked light is flashing and the washer is not draining, then there may be a problem with the drain pump. The drain pump helps to remove water from the washer tub. If the pump is defective, then the washer will not be able to drain properly. To test the drain pump, unplug the washer and remove the front panel. Locate the drain pump and check for any obstructions. If there are no obstructions, then the pump may be defective and will need to be replaced.
If the Whirlpool duet washer door locked light is flashing and the washer is not spinning, then there may be a problem with the drive belt. The drive belt helps to spin the washer tub. If the belt is damaged or loose, then the washer will not be able to spin properly. To test the drive belt, unplug the washer and remove the front panel. Locate the drive belt and check for any damage. If the belt is damaged, then it will need to be replaced.
If the Whirlpool duet washer door locked light is flashing and the washer is not filling with water, then there may be a problem with the water inlet valve. The water inlet valve controls the flow of water into the washer. If the valve is defective, then the washer will not be able to fill properly. To test the water inlet valve, unplug the washer and remove the front panel. Locate the water inlet valve and check for any obstructions. If there are no obstructions, then the valve may be defective and will need need to be replaced.
Whirlpool direct drive washer door locked light flashing?
If your Whirlpool washer door locked light is flashing, it could be caused by a few different things. But don’t worry, we’ll help you figure it out and get your washer running again in no time.
There are a few reasons why your Whirlpool direct drive washer door locked light might start flashing. One possibility is that the washer door isn’t closed all the way. Make sure to check that the door is shut tight before starting a cycle.
Another possibility is that something is blocking the washer door from closing properly. Take a look and see if there’s anything in the way of the door, like laundry detergent bottles or loose clothing. Once you’ve cleared the way, try closing the door again.
Whirlpool washer door locked and won’t open?
Here are some possible causes and solutions.
If your Whirlpool washer door is locked and won’t open, it could be because:
-There’s a power outage. Check to see if your home is experiencing a power outage. If so, wait until the power comes back on before trying to open the washer door.
-The washer is in use. If the washer is in use, it’s normal for the door to be locked. Once the cycle is finished, the door will unlock automatically.
-There’s a problem with the door latch. If there’s a problem with the door latch, you’ll need to contact a Whirlpool service technician for assistance.
-The washer is in pause mode. If the washer is in pause mode, simply press the “Start/Resume” button to resume the cycle and unlock the door.
Whirlpool washer door locked flashing and pump running?
This can be caused by a few things:
-The washer is overfilled and needs to be drained.
-There is something blocking the washer door from opening.
-The washer cycle was interrupted and needs to be reset.
If your washer is overfilled, you will need to drain it before you can continue using it. To do this, unplug the washer and remove the hose from the back of the machine. Place the hose in a bucket and turn on the water. Let the water run until it reaches a steady stream, then turn off the water and remove the hose.
If there is something blocking the washer door from opening, you will need to remove it before you can continue. Check the washer manual for instructions on how to do this.
If the washer cycle was interrupted, you will need to reset it. To do this, unplug the machine and then plug it back in. Press the power button to turn on the machine, then press the start/pause button. The washer should now be reset and you can continue using it.
How To Manually Unlock The Door On A Whirlpool Front Load Washer.
If your Whirlpool front load washer door is locked and you cannot open it, you may need to manually unlock the door. To do this, first locate the manual release button on the door. This button is usually located near the bottom of the door.
Once you have found the manual release button, press and hold it for a few seconds. The door should then unlock and you should be able to open it. If the door does not unlock, you may need to press and hold the button for a longer period of time or try pressing and holding it multiple times.
How To Manually Unlock The Door On A Whirlpool Top Load Washer.
If your washer door is locked and you cannot open it, there are a few things you can try to unlock it. First, unplug the washer from the power outlet. Next, locate the manual release cord on the bottom of the washer door.
The cord will have a red or black handle. Pull on the handle to release the door lock. If the door still does not open, push and hold the start/pause button for five seconds.
The washer should now be unlocked and the door should be able to be opened. Now that you know how to manually unlock the door on a Whirlpool top load washer, you can easily get your laundry done even when the door is locked.
Conclusion
If your Whirlpool washer door locked light is flashing, there are a few things you can do to fix the problem. First, check to make sure that the door is properly closed and latched. If it is, then try resetting the washer by unplugging it for 30 seconds and then plugging it back in. If the door locked light is still flashing, then you may need to replace the door lock switch.
We hope this blog post has helped you troubleshoot your Whirlpool washer door locked light issue. If you have any other questions or concerns, please feel free to contact us. Thanks for reading!
