14 Reasons Why Maytag Washer That’s Not Spinning: How To Fix

Last Updated on September 21, 2022 by Jason Nguyen

If your Maytag washer isn’t spinning, don’t worry – you’re not alone. This is a common problem that many people experience with this type of appliance.

In this blog post, we will provide you with a few tips on how to fix the problem. Follow these simple steps and your washer should be up and running in no time!

How to Fix a Maytag Washer That’s Not Spinning

1. Cycle Setting

If your washer is not spinning, the cycle setting may be incorrect. Check the dial or buttons to make sure the correct cycle has been selected.

If it is set to “rinse” or “spin,” your washer will not fill with water. The “drain and spin” setting should only be used for small loads that do not need to be washed.

2. Washer is Unbalanced or Overloaded

If your washer is overloaded, it will go into a suds lock. To fix this, simply redistribute the load by removing some clothes and restarting the cycle.

If your washer is unbalanced, pause the cycle and redistribute the load evenly around the drum. Then, restart the cycle.

3. Lid Switch Assembly

If your washer won’t start, the lid switch assembly might be defective. The lid switch ensures that the washer tub doesn’t fill while the lid is open.

You can test the lid switch with a multimeter to see if it’s defective. If the switch is defective, you’ll need to replace it.

Replacing the lid switch is a pretty straightforward repair. You’ll just need a screwdriver to remove the old switch and install the new one.

4. Drive Belt

If the drive belt is loose, frayed, or damaged, it can cause the washer not to spin. The drive belt is located under the tub on some models.

On other models, it is located behind the cabinet panels. Check your model’s manual for specific instructions on how to access and replace the drive belt.

You’ll need a putty knife, Phillips screwdriver, and pliers.

First, unplug the washer from the power outlet.
Remove the cabinet panels to access the drive belt.
Use the putty knife to pry off the clips that hold the panels in place.
Remove the screws that hold the panels in place with a Phillips screwdriver.
Lift the panels off of the washer.
Locate the drive belt and remove it from the washer.

To replace the drive belt, follow these steps:

First, find a replacement drive belt that is compatible with your model of Maytag washer. Remove the old drive belt from the washer.
Next, loop the drive belt around the washing machine’s pulley system.
Make sure that the belt is tight and secure.
Finally, replace the cabinet panels and screw them into place.

Now your Maytag washer should be spinning like new!

5. Motor Coupling

The motor coupling is located between the main wash tub and the drive system. The coupling connects and disconnects the power from the motor to the spin basket.

If your washer is not spinning, it could be due to a broken motor coupling.

You can check for a broken motor coupling by removing the front panel of your washer. Once you have access to the coupling, try to move it by hand. If the coupling is broken, you will be able to move it easily. If the coupling is not broken, it will be very difficult to move.

If your motor coupling is broken, you will need to replace it. This is a relatively easy repair that can be done with a few tools. You can find the replacement part at your local appliance store or online.

Once you have the new coupling, follow these steps to install it:

Unplug your washer from the power outlet.
Remove the front panel of your washer.
Disconnect the wires from the motor.
Remove the bolts that hold the motor in place.
Remove the old coupling and install the new one.
Reconnect the wires to the motor.
Replace the front panel of your washer.
Plug your washer back into the power outlet.

6. Door Latch

The door latch is the part of the washer that you use to open and close the door. If the door latch is not working, the washer will not be able to spin.

To fix this: You will need to replace the door latch. This is a fairly easy repair that you can do yourself.

First, you will need to remove the old door latch. This can be done by removing the screws that hold it in place.

Once the old door latch is removed, you can install the new one. Be sure to tighten the screws so that the new door latch is secure.

7. Drive Motor

The drive motor is responsible for turning the washer’s drum during the wash cycle. If the drive motor is defective, the washer may not spin. To determine if the drive motor is defective, first check to see if there are any loose or broken wires on it.

If everything looks okay, then remove the drive belt and try turning the drum by hand. If the drum does not turn freely, then the drive motor is likely defective and will need to be replaced.

How to prevent it?

You can prevent this by making sure to keep the washer’s drive belt tight and in good condition. Also, be sure to keep an eye on the drive motor for any signs of wear or damage. If you notice anything wrong, be sure to have it repaired or replaced as soon as possible.

8. Rotor Assembly

The rotor assembly is what helps the washer to spin. If this part is not working, then the washer will not be able to spin. This is a very important part of the washer and it needs to be fixed as soon as possible.

There are a few things that you can do to fix this problem. One thing that you can do is to check the belts. The belts could be loose or they could be broken. Another thing that you can do is to check the pulleys. The pulleys could be worn out or they could be damaged.

9. Stator Assembly

The stator assembly is located in the rear of the washer and contains the motor, drive pulley, and main tub.

If your Maytag washer is not spinning, it may be because the stator assembly has failed. The most common symptom of a failed stator assembly is a loud noise coming from the rear of the washer.

If you have a Maytag washer that is not spinning, you should check the stator assembly for damage. If the stator assembly is damaged, it will need to be replaced.

You can find the stator assembly for your Maytag washer at most appliance parts stores. Be sure to take the model number of your washer with you so that you can get the correct part.

Once you have the new stator assembly, follow these instructions to install it:

-First, remove the rear panel from the washer.

-Next, disconnect the electrical wiring from the motor.

-Then, remove the drive pulley from the motor.

-Finally, remove the main tub from the washer.

With the main tub removed, you will be able to access the stator assembly. To install the new stator assembly, simply reverse these steps. Be sure to reconnect all of the electrical wiring before putting the rear panel back on the washer.

10. Door Lock Motor and Switch Assembly

The door lock motor and switch assembly is an important part of your Maytag washer. This part is responsible for locking the door during the wash cycle. If your washer is not spinning, it could be because this part is not working properly.

You can check to see if the door lock motor and switch assembly is working by testing the door switch with a multimeter. If the door switch is not working, you will need to replace it.

You can find the door lock motor and switch assembly at most hardware stores or online retailers. Be sure to order the correct part for your model of washer.

Replacing the door lock motor and switch assembly is a relatively easy repair that you can do yourself. Be sure to unplug the washer before beginning this repair.

First, you will need to remove the door from the washer. To do this, simply unscrew the two screws that hold the door in place. Next, disconnect the wire harness from the door switch.

Then, remove the three screws that hold the door lock motor and switch assembly in place. Carefully pull out the old assembly and replace it with the new one. Be sure to reconnect the wire harness before screwing the new assembly in place.

Finally, screw the door back into place and test your washer to make sure it is spinning properly.

11. Motor Control Board

The Motor Control Board is the part of your washer that controls the spinning of the tub. If your Washer is not spinning, it may be due to a problem with this board.

Why does it fail?

There are a few reasons why this board may fail. The most common reason is due to a power surge. This can happen if there is a power outage or if the washer is plugged into an outlet that does not have proper grounding.

Another reason this board may fail is due to a manufacturing defect. In some rare cases, the board may simply be faulty.

How to fix it:

If the problem is due to a power surge, the best thing to do is unplug the washer and then plug it back in. This will reset the board and hopefully fix the problem.

If the problem is due to a manufacturing defect, you will need to replace the board. This is a fairly simple process and can be done by following the instructions in your owner’s manual.

Replacing the board is also a good idea if you are experiencing other problems with your washer, such as it not draining properly or not filling up with water. These could be signs that the board is failing and needs to be replaced.

12. Transmission

The transmission is a very important part of your washer. It helps to keep the washer spinning during the wash cycle and prevents the clothes from getting tangled. If your washer is not spinning, it could be because the transmission is not working properly.

There are a few things that you can do to try and fix this problem. First, you can check to see if the transmission is properly lubricated. If it is not, you can add some oil to it. You can also try resetting the transmission by turning off the power to the washer and then turning it back on again.

If none of these things work, you may need to replace the transmission. This is a fairly simple repair that you can do yourself. However, if you are not comfortable doing this, you can always call a Maytag repairman to come and do it for you.

13. Drain Filter

The drain filter is located on the bottom of your washer. If your washer is not draining, the first thing you should check is the drain filter.

To check the filter:

-Unplug your washer and remove the front panel.

-Locate the filter and unscrew it.

-If there is any lint or debris in the filter, clean it out.

-Screw the filter back on and replace the front panel.

-Plug your washer back in and try running a cycle.

14. Drain Pump

The drain pump helps to remove water from the washer. If the drain pump is not working, the washer will not spin.

There are a few things that you can do to try to fix this problem on your own. First, check to make sure that nothing is blocking the path of the drain pump.

This could be a sock or a piece of clothing that got caught in the washer. If something is blocking the path, remove it and see if the washer will start to spin.

If nothing is blocking the path of the drain pump, you may need to replace the drain pump. This is a relatively easy repair that you can do yourself. You can purchase a replacement drain pump online or at a local appliance store.

Related:

How to Fix a Maytag Washer That Won’t Start

Maytag bravos washer not spinning clothes dry?

If your Maytag Bravos washer is not spinning clothes dry, there could be several reasons why. Here are some possible causes and how to fix them:

-The washer may be overloaded. Try redistributing the load evenly and see if that helps.

-The washer’s spin cycle may be set too low. Try increasing the spin cycle speed and see if that helps.

-There may be something blocking the washer’s spinning mechanism. Check for any objects that could be blocking it and remove them if necessary.

-The washer’s drive belt may be loose or damaged. Try tightening or replacing the drive belt and see if that helps.

Related:

Maytag Atlantis washer not spinning?

If your Maytag Atlantis washer is not spinning, there are a few possible reasons. One possibility is that the washer is not getting enough power. Check to make sure that the washer is plugged in properly and that the circuit breaker has not tripped.

Another possibility is that the washer’s lid switch is not working properly. Try opening and closing the lid to see if that clears the problem. If neither of these solutions works, you may need to call a repairman.

Maytag washer not spinning burning smell?

There are a few potential causes for your Maytag washer to not spin and produce a burning smell. The most common cause is a clogged filter. Your washer’s filter traps lint, hair, and other debris from getting into the pump and causing damage. Over time, the filter can become clogged and cause your washer to not spin properly.

Another potential cause is a broken belt. The belt helps to rotate the drum during the washing cycle. If the belt is broken, your washer will not be able to spin.

If you’re experiencing these problems, there are a few things you can do to fix it. First, check your washer’s filter and clean it out if it is clogged. You can also check the belt for signs of wear or damage and replace it if necessary.

Maytag washer not spinning fast?

If your Maytag washer is not spinning fast, there could be a few different causes. One possibility is that the load of laundry is unbalanced. You can try redistributing the laundry in the washer and see if that makes a difference.

Another possibility is that something is blocking the washer’s spinning mechanism. Check to see if there is anything caught in the washing machine that could be preventing it from spinning properly.

If you can’t find anything, try running a cycle with nothing in the washer to see if that makes a difference.

Maytag washer not spinning and making noise?

If your Maytag washer is not spinning and making noise, there could be several reasons why. The first thing you should do is check the washer’s manual to see if there are any specific instructions on how to fix the problem. If not, here are some possible causes and solutions:

-The washer may be unbalanced. This can happen if there are too many clothes in the washer, or if the load is not evenly distributed. To fix this, redistribute the clothes in the washer and try again.

-There may be something caught in the washing machine’s pump. This could be a sock, a piece of clothing, or even a small object. To fix this, remove the item from the pump and try again.

-The washer’s drive belt may be loose. This can cause the washer to make noise and not spin correctly. To fix this, tighten the drive belt and try again.

-There may be something caught in the washing machine’s drain hose. This could be a sock, a piece of clothing, or even a small object. To fix this, remove the item from the drain hose and try again.

Old Maytag washer not spinning?

If your old Maytag washer isn’t spinning, it could be because of a clogged drain hose or a problem with the washing machine’s lid switch.

To fix a clogged drain hose, you’ll need to clean it out with a plunger or a plumber’s snake. If the problem is with the washing machine’s lid switch, you’ll need to replace it.

If your old Maytag washer still isn’t spinning, there could be a problem with the washing machine’s drive belt. The drive belt is what turns the washing machine’s drum. To fix this problem, you’ll need to replace the drive belt.

Conclusion

If your Maytag washer isn’t spinning, there are a few things you can try to fix the problem. First, check to make sure that the washer is plugged in and that the power cord is properly connected. Next, check the water supply hoses to ensure they are turned on and not kinked. Finally, take a look at the drive belt to see if it is broken or damaged.

If you can’t fix the problem yourself, call a Maytag service technician for assistance.