15 Reasons Why Maytag Dishwasher Not Draining: How to Fix

Last Updated on September 22, 2022 by Jason Nguyen

If your Maytag dishwasher isn’t draining properly, don’t worry – you’re not alone. This is a common problem that can usually be fixed quite easily. In this blog post, we will walk you through the steps to take to diagnose and fix the issue. So read on for all the information you need to get your dishwasher up and running again!

Related: 9 Dishwasher Brands To Avoid and 3 Most Reliable Brands

Maytag Dishwasher Not Draining: How to Fix the Problem

1. Drain Hose

The drain hose is the part of your dishwasher that allows water to drain out. If this hose becomes clogged, it can prevent your dishwasher from draining properly.

Why does it fail?

There are a few reasons why your dishwasher’s drain hose might become clogged. One is that food or other debris can build up in the hose, preventing water from flowing through it. Another possibility is that the hose itself is damaged and needs to be replaced.

How to fix it:

If your dishwasher’s drain hose is clogged, you’ll need to clear the obstruction. To do this, you can use a plunger or a plumber’s snake. If the hose is damaged, you’ll need to replace it with a new one.

2. Drain Filter

The Drain Filter is an important part of your dishwasher. It helps to keep food and other particles from clogging the drain.

If your dishwasher is not draining properly, it may be because the drain filter is dirty or clogged.

Why does it fail?

The Drain Filter can become dirty or clogged over time. If this happens, it can cause your dishwasher to not drain properly.

How do I fix it?

To clean the drain filter:

-Unplug the dishwasher.

-Remove the lower rack.

-Locate the drain filter (it will be in the bottom of the dishwasher, near the drain).

-Remove the drain filter and clean it with warm, soapy water.

-Replace the drain filter and lower rack.

-Plug in the dishwasher and run a rinse cycle.

3. Garbage Disposal

Your Maytag dishwasher not draining could be caused by a clogged garbage disposal.

Why does it fail?

Over time, your garbage disposal can become clogged with food particles and grease. This can cause the dishwasher to back up and not drain properly.

How do you fix it?

You’ll need to unclog the garbage disposal. First, turn off the power to the disposal at the circuit breaker. Then, use a plunger to try to dislodge the clog.

If that doesn’t work, you’ll need to use a plumbing snake to clear the clog. Finally, turn the power back on and run the dishwasher through a cycle to make sure it’s draining properly.

4. Drain Impeller

The drain impeller is a small, rubber-like part that helps push water through the dishwasher’s drainage system.

If the impeller is damaged or broken, it can cause water to leak from the dishwasher or not drain properly.

To check if the impeller is damaged:

-Remove the dishwasher’s lower access panel.

-Locate the impeller on the bottom of the dishwasher.

-Inspect the impeller for cracks or damage.

If the impeller is damaged, it will need to be replaced. To replace the impeller:

-Remove the dishwasher’s lower access panel.

-Locate the impeller on the bottom of the dishwasher.

-Remove the impeller by unscrewing it from the motor shaft.

-Install the new impeller by screwing it onto the motor shaft.

-Replace the dishwasher’s lower access panel.

5. Drain Pump

If your dishwasher doesn’t seem to be draining properly, the first thing you should check is the drain pump. The drain pump helps to circulate water through the dishwasher and then pumps it out. If the pump is clogged or damaged, it can cause your dishwasher to not drain properly.

There are a few things you can do to clean or replace the drain pump. First, you can try cleaning it with a brush or a vacuum cleaner. If this doesn’t work, you may need to replace the pump.

Replacing the drain pump is not a difficult task, but it is important to make sure that you get the right pump for your dishwasher. You can find the right pump by checking your owner’s manual or contacting a Maytag customer service representative.

Once you have the new pump, simply follow the instructions in your owner’s manual to install it. If you have any trouble, you can always contact a Maytag customer service representative for help.

6. Drain Solenoid Kit

The Drain Solenoid Kit is a replacement part for your Maytag dishwasher. This part is responsible for draining water from the dishwasher. If your dishwasher is not draining properly, this kit can help fix the problem.

This kit includes a drain solenoid, a mounting bracket, and two screws. It is easy to install and comes with detailed instructions.

7. Drain Valve

The Maytag dishwasher not draining can be caused by a clogged drain valve. The drain valve is located at the bottom of the dishwasher, and it is responsible for draining water from the dishwasher.

If the drain valve becomes clogged, it will prevent water from draining from the dishwasher. To fix this problem, you will need to clean the drain valve.

Instructions:

To clean the drain valve, you will need to remove it from the dishwasher. To do this, you will need to unscrew the drain valve from the bottom of the dishwasher.

Once you have removed the drain valve, you can then clean it with a brush or a toothpick. Once you have cleaned the drain valve, you can then screw it back into the bottom of the dishwasher.

8. Air Gap

If your dishwasher isn’t draining properly, one possible culprit is the air gap. The air gap is a small device that’s usually mounted on the sink or countertop near the dishwasher. Its purpose is to prevent dirty water from flowing back into the dishwasher.

There are two common ways that an air gap can become clogged. The first is when food particles and other debris get caught in it. This can happen if you don’t clean the air gap regularly. The second way is when grease builds up inside the air gap.

9. Timer

The timer is responsible for two things in a dishwasher: how long the cycle runs, and when the dishwasher actually starts.

If your Maytag dishwasher isn’t draining properly, it could be due to a problem with the timer. In this case, you’ll need to replace the timer. Here’s how:

First, locate the timer. It’s usually located near the control panel, and it may be hidden behind a kickplate or access panel. Once you’ve found it, unplug the dishwasher from the power source.

Next, remove the screws that hold the timer in place, and carefully pull it out. Take note of how it’s wired, so you can wire the new timer in the same way.

Now, it’s time to install the new timer. Simply reverse the steps you took to remove the old one, and make sure all the wires are properly connected.

Once that’s done, plug the dishwasher back in and test it out. If everything is working properly, your dishwasher should now be draining correctly.

10. Wrong Type of Detergent

If you have a dishwasher, chances are you’re using the wrong type of detergent. Dishwashing detergent is different than laundry detergent and other types of cleaners. If you use the wrong type of detergent, your dishes won’t come clean and your dishwasher could be damaged.

Most dishwashing detergents are made for use in dishwashers. They’re designed to be low-sudsing and to work well with the dishwasher’s cycle. Laundry detergent is designed to be high-sudsing and it can damage your dishwasher if you use it.

Other types of cleaners, like all-purpose cleaners and bathroom cleaners, aren’t made for use in dishwashers. They can damage the dishwasher and they won’t clean your dishes properly.

If you’re not sure what type of detergent to use, check the label on the dishwashing detergent. It should say that it’s safe for use in dishwashers. If you can’t find a dishwashing detergent, ask your local hardware store or home improvement store for help.

11. Pump and Motor Assembly

The pump and motor assembly is located beneath the dishwasher. It is responsible for drawing water from the dishwasher tub and pumping it through the drain hose.

If your Maytag dishwasher is not draining, it could be because there is something blocking the pump and motor assembly. To clean this, first remove any food or debris that may be blocking the assembly.

Then, use a brush or cloth to clean any dirt or grime that may be build up on the assembly. If your dishwasher still will not drain, it is possible that the pump and motor assembly itself is defective and will need to be replaced.

If you have determined that the pump and motor assembly needs to be replaced, follow these steps:

-First, unplug the dishwasher from the power outlet and turn off the water supply to the dishwasher.

-Next, remove the lower dishrack and silverware basket from the dishwasher.

-Then, use a screwdriver to remove the screws that secure the pump and motor assembly to the bottom of the dishwasher.

-Carefully remove the assembly from the dishwasher and take it to a local appliance repair shop to have it replaced.

-Finally, reassemble the dishwasher and plug it back into the power outlet. Turn on the water supply and run a test cycle to ensure that the dishwasher is draining properly.

12. Check Valve

The check valve is located on the dishwasher’s drain hose. The function of the check valve is to prevent water from flowing back into the dishwasher.

If the check valve is not working properly, it could cause water to back up into your dishwasher and cause problems with draining.

To test the check valve:

-Disconnect the dishwasher from the power source.

-Remove the drain hose from the dishwasher.

-Place a bucket under the end of the drain hose that is not connected to the dishwasher.

-Turn on the water and let it run for a few minutes.

-If water starts flowing out of the end of the drain hose, the check valve is working properly.

-If water does not start flowing out of the end of the drain hose, the check valve is not working properly and will need to be replaced.

13. Check Ball

If your dishwasher is not draining, the first thing you should check is the check ball. The check ball is located at the bottom of the dishwasher and is responsible for stopping water from entering the dishwasher when it is not in use.

If the check ball becomes damaged or dislodged, it can cause your dishwasher to not drain properly.

To check the check ball:

-Remove the dishwasher from its power source.

-Disconnect the drain hose from the dishwasher.

-Remove the lower access panel to gain access to the check ball.

-Inspect the check ball for damage or debris. If the check ball is damaged, it will need to be replaced. If there is debris on the check ball, clean it off and reassemble the dishwasher.

-Turn on the dishwasher to see if it is now draining properly. If not, you may need to call a qualified technician to further troubleshoot your dishwasher.

14. Drain Hose

The drain hose is the part of your dishwasher that drains water out of the tub. It is usually made of flexible PVC or rubber, and is about three to five feet long. The hose attaches to the drain pump, which is located under the dishwasher tub.

If your dishwasher is not draining properly, the first thing you should check is the drain hose. Make sure that it is not kinked or clogged. If it is, straighten it out or clear the obstruction. Also, make sure that the hose is not loose at either end. Tighten any loose connections.

15. Water Pump Belt

About this: The water pump belt is located under the dishwasher and helps to move the water through the dishwasher during the cycle. This part can become worn or damaged over time and may need to be replaced.

To replace the water pump belt, you will need to:

  • Remove the dishwasher from its location
  • Disconnect the power supply
  • Remove the access panel
  • Locate the water pump belt
  • Remove the old water pump belt
  • Install the new water pump belt
  • Replace the access panel
  • Reconnect the power supply
  • Place the dishwasher back in its location

Related:

Why does my Maytag dishwasher have water in the bottom?

It could be a few different things. First, check to see if the dishwasher is overfilling. If the float switch isn’t working properly, it could be letting too much water into the dishwasher.

Another possibility is that the drain hose is clogged or not installed correctly. Finally, make sure that the siphon break isn’t faulty.

This part is responsible for draining water out of the dishwasher. If it isn’t working properly, water will build up in the bottom of the dishwasher.

Maytag dishwasher not draining at end of cycle?

maytag dishwasher not draining at end of cycle

If your Maytag dishwasher is not draining at the end of the cycle, there are a few things that could be causing the problem. In this article, we’ll go over some of the most common causes and how to fix them.

One of the most common reasons why your Maytag dishwasher might not be draining properly is because there is something blocking the drain line. If there is food or other debris caught in the drain line, it can prevent the water from draining properly. To fix this, you’ll need to clean out the drain line.

Another common reason for a dishwasher not draining properly is that the pump is damaged or malfunctioning. The pump is responsible for moving the water through the dishwasher, so if it’s not working properly, the dishwasher won’t be able to drain properly. To fix this, you’ll need to replace the pump.

If your dishwasher is still not draining properly after trying these two fixes, then there may be an issue with the float switch. The float switch is responsible for sensing when the water level in the dishwasher is too high and shutting off the dishwasher to prevent flooding. If the float switch is damaged or stuck, it can prevent the dishwasher from draining properly. To fix this, you’ll need to replace the float switch.

Maytag Dishwasher Not Fully Draining

maytag dishwasher not fully draining

If your Maytag dishwasher isn’t draining properly, there are a few things you can check to try and fix the issue.

1. Float valve

The float valve is a device located in the dishwasher that allows water to enter the dishwasher. The float valve is also responsible for stopping the flow of water into the dishwasher when the dishwasher is full.

If your Maytag dishwasher is not draining properly, it could be because the float valve is not working correctly.

To test the float valve, first make sure that the dishwasher is turned off and the water supply to the dishwasher is turned off. Then, remove the float valve from the dishwasher and check to see if it is clear of debris. If the float valve is clogged, clean it with a toothbrush or other small brush.

Once you have cleaned the float valve, reattach it to the dishwasher and turn on the water supply. Turn on the dishwasher and let it run through a cycle. If the dishwasher still does not drain properly, you may need to replace the float valve.

2. Wrong detergent

If you are using the wrong detergent in your Maytag dishwasher, it may not fully drain. This can cause a number of problems, including leaving soap residue on your dishes and causing the dishwasher to overflow.

There are a few things you can do to prevent this from happening:

  • Use only recommended detergents in your dishwasher.
  • Follow the manufacturer’s instructions on how to load your dishwasher.
  • Be sure to run your dishwasher through a complete cycle before adding more detergent.

3. Air gap

The air gap is a small device mounted on the sink or countertop near the dishwasher. Its purpose is to prevent water from siphoning back into the dishwasher. If your dishwasher isn’t draining properly, one possible reason is that the air gap is blocked.

To clean the air gap:

  • Unscrew the cap from the air gap.
  • Use a toothpick or other small object to clear any debris from the holes in the air gap.
  • Rinse out the air gap with water and screw the cap back on.

4. Time delay

One possibility is that the time delay feature is turned on. This feature allows you to set the dishwasher to run at a later time, which can be handy if you want to run it overnight or when you’re not home.

However, if the time delay is turned on, the dishwasher may not start draining until the specified time. So, if you’re noticing that your dishwasher isn’t draining right away, check to see if the time delay feature is turned on and adjust accordingly.

Old Maytag dishwasher not draining?

old maytag dishwasher not fully draining

There are a few things that could be causing this. First, check to see if there is anything blocking the dishwasher’s drain hose. If there is, remove it and try running the dishwasher again.

If the dishwasher still doesn’t drain, then the problem may be with the pump. To test this, disconnect the power to the dishwasher and then remove the drain hose from the pump. Next, check to see if the impeller (the part of the pump that moves water) is free to move.

If it isn’t, then you will need to replace the pump. Finally, if the dishwasher still doesn’t drain, then there may be a problem with the float switch. This switch is what tells the dishwasher when to stop pumping water.

To test this, disconnect the power to the dishwasher and then remove the float switch. If the switch is stuck in the “up” position, then you will need to replace it.

New Maytag dishwasher not draining?

If your new Maytag dishwasher isn’t draining properly, there are a few potential causes. One possibility is that the drain hose is kinked or clogged. Another possibility is that the garbage disposal is jammed or clogged. Finally, the float switch may be stuck in the “on” position.

To fix a kinked or clogged drain hose, simply unkink the hose or clear the obstruction. To fix a jammed or clogged garbage disposal, you’ll need to remove the obstruction. To fix a stuck float switch, you’ll need to replace it.

Maytag dual power filtration dishwasher not draining?

Check for these common causes and how to fix them.

Maytag dual power filtration dishwasher not draining? The most common cause is a clogged sink trap. To clear a clogged sink trap, remove the dishwasher drain hose from the disposal unit and check the sink trap for debris. If the sink trap is clear, reattach the dishwasher drain hose and run a cycle to see if the dishwasher drains properly.

Another common cause of a dishwasher not draining is a clogged garbage disposal unit. If your garbage disposal unit is clogged, you’ll need to clear it before your dishwasher will drain properly.

To clear a clogged garbage disposal unit, remove the dishwasher drain hose from the disposal unit and use a plunger to clear the clog. Once the clog is cleared, reattach the dishwasher drain hose and run a cycle to see if the dishwasher drains properly.

Maytag performance dishwasher not draining?

If your dishwasher isn’t draining properly, there are a few possible causes. First, check the drain hose to make sure it’s not clogged or kinked.

Next, clean the filters to remove any buildup of food or grease. Finally, run a test cycle with vinegar to clean the dishwasher’s interior and remove any soap scum.

Maytag gold series dishwasher not draining?

There are a few things that could be causing this. First, check to make sure that the dishwasher is turned on and the door is shut correctly. If the dishwasher is on and the door is shut, but it’s still not draining, then there are a few other things you can check.

One possible reason why your Maytag gold series dishwasher is not draining properly is that the drain hose is clogged. The drain hose is the hose that goes from the dishwasher to the drainage system in your home.

If this hose is clogged, then it will prevent water from draining out of the dishwasher. To check if the drain hose is clogged, disconnect it from the dishwasher and check to see if there is any debris blocking the hose. If there is, then you’ll need to clear the debris so that water can flow through freely.

Another possible reason why your Maytag gold series dishwasher is not draining properly is that the drainage system in your home is clogged. This is most likely to happen if you have a septic tank. If the drainage system in your home is clogged, then it will need to be cleared so that water can flow through freely.

Conclusion

If your Maytag dishwasher is not draining, there are a few things you can do to try and fix the problem. First, check the drain hose to make sure it is not clogged or blocked. Next, check the garbage disposal to see if it is jammed or clogged. Finally, if neither of these solutions work, you may need to call a professional to come and take a look at your dishwasher. Thank you for reading! We hope this article was helpful.