Frigidaire Refrigerator Water Dispenser Not Working: How to Fix It

Last Updated on January 29, 2024 by Kimberly Crawford

If your Frigidaire refrigerator water dispenser is not working, don’t worry – you can fix it! In this blog post, we will walk you through the steps to take to get your water dispenser up and running again. We will also provide some tips on how to prevent this from happening in the future.

Reasons Why Frigidaire Refrigerator Water Dispenser Not Working

1. Dispenser Control Board.

If your water dispenser is not working, the first thing you should check is the dispenser control board. This controls the water dispenser and can sometimes become faulty.

To test it, simply unplug the refrigerator and remove the dispenser control board. You can then test it with a multimeter to see if it is receiving power. If not, then you will need to replace it.

How does it fail?

The dispenser control board can fail in a few ways. The most common way is for the board to short circuit. This can happen if the board becomes wet or if there is a problem with the wiring.

Another way the dispenser control board can fail is by failing to provide power to the water dispenser. This can be caused by a problem with the fuse or by a problem with the power supply.

Finally, the dispenser control board can also fail by failing to send a signal to the water dispenser. This can be caused by a problem with the wiring or by a problem with the control board itself.

How to fix it?

The best way to fix this is to replace the control board with a new one.

Replacing the dispenser control board is a pretty easy task that most people can do themselves.

First, you will need to locate the control board. It is usually located behind the water dispenser.

Next, you will need to disconnect the power to the refrigerator. Be sure to unplug it from the wall or turn off the circuit breaker before proceeding.

Once the power is disconnected, you will need to remove the screws that hold the control board in place.

Once the screws are removed, you can pull out the old control board and insert the new one. Be sure to line up the holes before inserting the screws.

Once the new control board is in place, you can reconnect the power and test out the water dispenser.

2. Dispenser Switch.

The dispenser switch is a switch that controls the water dispenser.

If your fridge’s water dispenser isn’t working, one possible reason is that the dispenser switch has become faulty.

This switch can be located in different places depending on your fridge model, so you’ll need to consult your refrigerator’s manual to find it. Once you’ve found the switch, you can test it using a multimeter to see if it’s working properly.

How does it fail?

The dispenser switch can fail in two ways:

-It can become stuck in the “on” position, meaning that water will constantly flow from the dispenser even when you don’t want it to.

-It can become stuck in the “off” position, meaning that water will never flow from the dispenser no matter how often you press the lever.

What are the symptoms?

If the dispenser switch is stuck in the “on” position, you’ll probably notice water constantly dripping or flowing from the dispenser. If it’s stuck in the “off” position, you won’t be able to get any water from the dispenser no matter how often you press the lever.

How do you fix it?

If the dispenser switch is stuck in the “on” position, you’ll need to replace it. If it’s stuck in the “off” position, you can try cleaning it with a cotton swab soaked in rubbing alcohol. if that doesn’t work, you’ll need to replace it.

To replace the dispenser switch, you’ll need to remove the front panel of your fridge. This will give you access to the switch. Once you’ve removed the old switch, you can install the new one by following the instructions in your refrigerator’s manual.

3. Door Switch.

The door switch signals the fridge to turn on the water and ice dispenser when the refrigerator door is opened.

Where is it located?

The door switch is usually located near the top of the fridge, near where the door hinges are.

What does it look like?

It’s a small plastic piece with two metal prongs sticking out of it.

How does it fail?

One way the door switch can fail is if the ice maker switch is turned on when the refrigerator door is open. This will cause the water dispenser to turn off.

Another way the door switch can fail is if the refrigerator door is left open for too long and the temperature inside gets too warm. This will cause the water dispenser to turn off.

How do I know if it’s broken?

If the water and ice dispenser don’t work when you open the fridge door, the door switch might be broken.

How do I fix it?

To fix this, first make sure the ice maker switch is turned off. If the refrigerator door is left open, close it and wait for the temperature inside to cool down. If neither of these fixes work, then the door switch will need to be replaced.

To replace the door switch:

-First, locate the switch. It is usually located near the top of the fridge, near the hinges.

-Next, disconnect the power to the fridge. This can be done by unplugging it from the wall or by flipping the circuit breaker.

-Once the power is disconnected, remove the screws that hold the switch in place.

-Carefully pull the switch out, taking note of how it is wired.

-Attach the new switch in the same position and screw it in place.

-Reconnect the power to the fridge and test the new switch by opening and closing the door. The water dispenser should turn on and off as the door is opened and closed.

4. Low Water Pressure.

If your water pressure is low, your refrigerator’s water dispenser will not work. Check your home’s water pressure to see if it is within the normal range of 40 to 60 PSI.

If it is not, you will need to adjust your home’s water pressure. You can do this by adjusting the knob on your home’s main water valve.

5. Water line.

The water line is the most likely culprit if your Frigidaire refrigerator’s water dispenser suddenly stops working.

Inspect the water line for kinks or leaks. If there are any, you’ll need to replace the entire water line.

6. Water Filter.

The water filter is located in the back, right corner of your refrigerator. It purifies the water that comes into your home through the municipal water supply.

Over time, it can become clogged with sediment and other contaminants, which can reduce its effectiveness.

How does it fail?

There are a few ways that the water filter can fail. The most common is simply because it needs to be replaced after a certain amount of time. Depending on the model of your refrigerator, the manufacturer may recommend replacing it every six months or so.

Another way that the water filter can fail is if it becomes clogged with sediment and other contaminants. This can happen if you live in an area with hard water or if your municipality’s water supply is not properly treated.

Finally, the water filter can also fail if it is not installed properly. This can happen if you do not follow the manufacturer’s instructions correctly or if you try to install it yourself without professional help.

What are the symptoms?

If your water filter is not working properly, you may notice that the water dispenser is not working as well. The water may come out slowly or there may be no water coming out at all.

You may also notice that the ice maker is not working as well. The ice cubes may be smaller than usual or there may be no ice cubes at all.

If you notice any of these symptoms, it is important to check the water filter to see if it needs to be replaced or cleaned.

How do I fix it?

If your water filter needs to be replaced, follow the manufacturer’s instructions for doing so. If you are not sure how to do this, consult a professional appliance repair person.

If your water filter is clogged, you can try flushing it with clean water. To do this, remove the filter from your refrigerator and hold it under running water for a few minutes. If this does not work, you may need to purchase a new filter. Consider checking All Filters for a suitable fridge filter replacement.

Finally, if your water filter is not installed properly, follow the manufacturer’s instructions for doing so or consult a professional appliance repair person. Do not try to install it yourself unless you are absolutely sure that you know what you are doing.

7. Water Inlet Valve.

The water inlet valve is an electrically-operated valve that controls the flow of water into the refrigerator.

Where is it located?

The water inlet valve is usually located behind the refrigerator, near the bottom.

How does it work?

When you press the button or lever to dispense water from your fridge, a signal is sent to the water inlet valve to open and allow water to flow into the fridge.

What can go wrong with it?

If the water inlet valve is defective, it may not open when you press the lever or button, or it may not close properly after the water has been dispensed. This can cause a leak.

How do I fix it?

If your water inlet valve is defective, you will need to replace it.

To replace the water inlet valve:

-Turn off the water supply to the refrigerator.

-Disconnect the water line from the valve.

-Remove the screws that hold the valve in place.

-Pull out the old valve and insert the new one.

-Reconnect the water line to the new valve.

-Turn on the water supply.

-Test the new valve by dispensing water from the fridge.

8. Water Tank.

The water tank is a small, round container that sits on top of the fridge. It holds about two gallons of water and has a spigot that dispenses water into your glass.

If your refrigerator’s water dispenser is not working, one possible reason is that the water tank might be empty. Check to see if the tank needs to be refilled.

9. Water Tube.

The water tube is the clear plastic tubing that runs from the back of your fridge to the water dispenser. If this tubing becomes kinked or damaged, it can cause your water dispenser to stop working.

How do I fix it?

Start by unplugging your fridge and then locate the water tube at the back of your fridge

Replacing the water tube is a fairly simple process that anyone can do. Just follow these steps:

-First, unplug your refrigerator and turn off the water supply to your fridge.

-Next, locate the water tube at the back of your fridge. You may need to remove a few screws to access it.

-Once you have located the water tube, simply cut out the damaged section and replace it with a new piece of tubing.

-Finally, turn the water back on and plug your fridge back in. Your water dispenser should now be working properly.

Related: GE Refrigerator Water Dispenser Not Working: How to Fix

The frigidaire refrigerator water dispenser not working but the ice maker is?

This is a frustrating problem because you need water to make ice. There are a few potential causes of this issue. Let’s explore them so you can get your dispenser working again.

One potential cause is that the water line leading to the dispenser may be frozen. Check the line for any signs of frost or ice buildup. If you see any, thaw it out with a hair dryer.

Another potential cause is that the dispenser itself may be dirty. Over time, dirt and grime can build up on the dispenser’s surface, preventing it from working properly. Clean the dispenser with a mild soap and water solution.

If neither of these solutions fixes the problem, there may be an issue with the water supply line. Check to see if the line is kinked or damaged in any way. If it is, you’ll need to replace it.

Frigidaire refrigerator water and ice dispenser not working?

frigidaire refrigerator water ice dispenser not working

Here are some possible causes and how to fix it.

The most common reason why your Frigidaire refrigerator’s water and ice dispenser might not be working is because the filter might be clogged. The filter is responsible for removing impurities from the water, so if it’s clogged, the water can’t flow properly. To fix this, you’ll need to replace the filter.

Another possible reason why your water and ice dispenser might not be working is because the water line might be frozen. This usually happens if the temperature in your fridge is set too low.

To thaw a frozen water line, turn off the fridge and disconnect the water line from the back of the fridge. Then, use a hair dryer to thaw the frozen line. Once the water line is thawed, reconnect it and turn on the fridge.

Frigidaire refrigerator water dispenser not working after replacing filter.

frigidaire refrigerator water ice dispenser not working after change filter

If your Frigidaire refrigerator water dispenser is not working after replacing the filter, it could be due to one of several issues. The most common cause is that the water filter is not properly installed.

Another possibility is that the water line has become clogged. Finally, there could be an issue with the water pressure.

If the water filter is not properly installed, the first thing you should do is check the manufacturer’s instructions to make sure you have installed it correctly. If the problem persists, try flushing the filter with clean water to remove any debris that may be blocking the flow of water.

If the water line has become clogged, the best way to fix it is to call a professional. However, if you are comfortable working with plumbing, you can try to clear the clog yourself. First, turn off the water supply to the refrigerator.

Next, disconnect the water line from the fridge and use a plunger or pliers to remove any obstructions from the line. Finally, reconnect the water line and turn on the water supply.

If the water pressure is too low, you may need to adjust the pressure regulator. This is a relatively simple task that can be done with a wrench. First, locate the pressure regulator on the water line leading to the fridge. Next, use a wrench to turn the adjusting screw until the desired pressure is reached.

Frigidaire refrigerator water dispenser hot water not working.

There are a few things that could be causing this problem. The first thing to check is the water line. If the water line is kinked, it could be restricting the flow of water to the dispenser.

Another possibility is that the water filter is clogged and needs to be replaced. Finally, if the hot water heater is set too low, it could be causing the water to be dispensed at a lower temperature than what is set on the refrigerator.

If the water line is kinked, the first thing to do is straighten it out. If that doesn’t fix the problem, then check the water filter and replace it if necessary. If the hot water heater is set too low, try adjusting it to a higher setting. If none of these solutions work, then you may need to call a plumber or an appliance repair person to come take a look at your fridge.

Frigidaire Refrigerator Not Dispensing Cold Water.

There are a few things that could be causing your Frigidaire refrigerator to not dispense cold water. Here are a few causes and solutions:

-The first thing you should check is the water filter. If it is clogged, it will need to be replaced.

-If the water filter is not the problem, then the next thing to check is the water inlet valve. This valve controls the flow of water into the refrigerator, and if it is not working properly, it could be causing the problem.

-Another possible cause of your Frigidaire refrigerator not dispensing cold water could be a clogged water line. If this is the case, you will need to clean the water line.

-Finally, if none of these solutions solve the problem, you may need to call a professional to come and take a look at your refrigerator.

How do you reset the water dispenser on a Frigidaire refrigerator?

If your Frigidaire refrigerator’s water dispenser is not working, you may need to reset it. To do this, first locate the reset button on the back of the fridge. Once you’ve found the reset button, press and hold it for three seconds. After that, try using the water dispenser again and see if it works.

Where is the water filter reset button on a Frigidaire refrigerator?

The water filter reset button is located on the control panel of your refrigerator. To reset the water filter, simply press and hold the button for three seconds.

Related: Frigidaire Refrigerator Not Cooling? 6 Reasons Why and How to Fix Them

Conclusion

If your Frigidaire refrigerator water dispenser is not working, there are a few things you can do to fix it. First, check the water line for leaks. If there are no leaks, then the problem may be with the water pressure. Adjust the water pressure until it is at a normal level. If that does not fix the problem, then you may need to replace the water filter. Finally, if all else fails, you can contact a Frigidaire refrigerator repair service for help.

We hope this blog post was helpful in troubleshooting your Frigidaire refrigerator water dispenser issue. For more appliance tips and tricks, be sure to check out our other blog posts. Thanks for reading!