Last Updated on November 25, 2023 by Kimberly Crawford
If your Whirlpool refrigerator ice maker isn’t working, you’re not alone. This is a common problem that often requires little more than a quick fix.
In this blog post, we will discuss some of the most common reasons why your ice maker might not be working and provide you with some solutions to get it up and running again.
Reasons Why Whirlpool Refrigerator Ice Maker Not Working: What to Do
1. Ice Maker is OFF.
If your ice maker has an ON/OFF switch, make sure it is turned to the ON position. If you have a refrigerator with a water dispenser and ice maker in the door, check that the ice shut-off arm is not in the OFF position.
The arm is usually white and located on the right side of the refrigerator, just above the ice bucket.
If the arm is in the up position, it is off. Push it down to turn it on. Also, make sure that there is no ice build-up around the ice maker unit so that it can operate properly.
If your refrigerator does not have an ON/OFF switch and the shut-off arm is in the ON position, continue troubleshooting below.
2. Freezer Temperature.
Check the freezer temperature. The ideal freezer temperature is between 0°F and 5°F. If the freezer isn’t cold enough, the ice maker won’t work.
Check to see if there are any food items blocking the airflow in the freezer. Also, make sure that the vents at the back of the freezer are not blocked.
3. Water Inlet Valve.
The water inlet valve is an electrically-operated valve that controls the flow of water into the ice maker.
If this valve is defective, it may leak water into the ice maker, or it may not allow enough water to enter the ice maker.
Why does it fail?
If the water inlet valve is clogged with ice, it will not allow enough water to flow into the ice maker.
What are the symptoms?
If the water inlet valve leaks water into the ice maker, you may notice puddles of water on the floor near the refrigerator.
If the valve does not allow enough water to enter the ice maker, the ice cubes may be small or there may not be enough ice cubes.
How to test it:
You will need a multimeter to test the water inlet valve for continuity. To do this, first unplug the refrigerator from the power outlet.
Then remove the two screws that secure the water inlet valve to the refrigerator. Next, disconnect the two wires from the water inlet valve.
Finally, use the multimeter to test for continuity between the two terminals on the water inlet valve. If there is no continuity, then the water inlet valve must be replaced.
How can I prevent it from happening again?
You can prevent this problem from happening again by making sure that the water line that supplies the ice maker is not frozen.
If the water line freezes, it will not be able to supply enough water to the ice maker and the ice cubes will be small or there may not be enough ice cubes.
4. Ice Maker Assembly.
The ice maker assembly is what actually makes the ice. It contains the mold that the water is filled in to make cubes, as well as the ejector arm that pushes the cubes out.
If your refrigerator’s ice maker isn’t working, there’s a good chance that it’s because of a problem with this part.
Why does it fail?
There are a few different reasons why an ice maker assembly might fail. One is that the mold might be broken, preventing it from properly filling with water.
Another is that the ejector arm could be jammed, preventing the ice cubes from being pushed out. Finally, there could be an issue with the water inlet valve, which supplies water to the mold.
How do you fix it?
If the problem is with the mold, you’ll need to replace the entire assembly. However, if the problem is with the ejector arm or water inlet valve, you may be able to replace just those parts. Consult your refrigerator’s manual to see what parts are available for replacement.
How can I prevent it from happening again?
There’s not much you can do to prevent an ice maker assembly from failing. However, you can make sure that your refrigerator is properly maintained.
This includes regularly cleaning the ice maker (including the mold) and making sure that there’s no build-up of ice anywhere in the unit. Additionally, be sure to replace any worn or damaged parts as soon as possible to prevent further issues.
5. Icemaker Module.
AThe icemaker module is located in the freezer.
If your refrigerator’s ice maker isn’t working, there are a few things you can check yourself before calling a technician.
The most common issue is that the icemaker module is not getting power. First, check to make sure that the ice maker switch is turned on. If it is, then check the circuit breaker or fuse to see if it needs to be reset or replaced.
Why does it fail?
The most common reason for an ice maker to fail is because it is not getting power. If the ice maker switch is turned on, check the circuit breaker or fuse to see if it needs to be reset or replaced.
Other possible causes include a clogged water filter, a frozen water line, or a problem with the control board.
How to fix it?
If the issue is that the icemaker module is not getting power, you can try resetting the circuit breaker or replacing the fuse. If that doesn’t work, you’ll need to call a technician.
To reset the circuit breaker, simply flip it off and then back on again. If the fuse needs to be replaced, you can find the correct size and type of fuse at your local hardware store.
How can I prevent it from happening again?
There are a few things you can do to prevent your ice maker from failing. First, make sure to regularly replace your refrigerator’s water filter.
A clogged filter can cause the ice maker to stop working. You should also clean the ice bin every few months to prevent build-up of mold and bacteria.
Finally, be sure to keep the area around your refrigerator clean and free of clutter. This will help ensure adequate airflow and prevent the ice maker from overworking.
6. Low Water Pressure.
One possible reason why your Whirlpool refrigerator’s ice maker is not working could be low water pressure. Check to see if the water pressure to your fridge is adequate.
How to fix it?
If the water pressure is low, you’ll need to increase it. You can do this by cleaning the inlet screen on the water line that leads to your fridge.
7. Door Switch.
The door switch signals the ice maker to start when the door is closed. If it’s defective, the ice maker won’t make ice.
To check if your door switch is working, open your refrigerator door and look for a little metal arm on the right side (it should be attached to the fridge). If that arm is up, then your switch is off. If it’s down, then your switch is on.
If your door switch is on and your ice maker still isn’t working, then the problem is most likely with the ice maker itself and will need to be replaced.
Why does it fail?
Door switches fail most often because of age and wear. Over time, the switch can become less sensitive, eventually to the point where it won’t register that the door has been opened or closed.
Another reason for failure is dirt and debris build-up on the switch contacts. This can prevent the switch from making a good connection, which prevents the ice maker from getting power.
Cleaning the door switch contacts with a cotton swab or toothpick can often restore proper operation. If that doesn’t work, you’ll need to replace the door switch. Fortunately, this is an easy repair that anyone can do.
How to fix it?
To test the door switch, open the refrigerator door and press the switch with your finger. If the light doesn’t come on, then you know the switch is bad and will need to be replaced.
Replacing a door switch is easy and only requires a few simple tools. You’ll need a putty knife, Phillips screwdriver, and a new door switch.
First, use the putty knife to pry off the plastic cover on the switch. Then, remove the two screws that hold the switch in place. Be careful not to lose them!
Next, disconnect the wire harness from the old switch and connect it to the new one. Finally, screw the new switch in place and snap on the plastic cover. That’s it!
How can I prevent it from happening again?
There’s not much you can do to prevent a door switch from failing. However, you can extend its life by regularly cleaning the contacts with a cotton swab or toothpick. This will help prevent dirt and debris build-up that can cause the switch to fail prematurely.
You should also avoid slamming the refrigerator door too hard, as this can damage the switch. If you have small children, you may want to consider installing a door stop to prevent them from accidentally breaking the switch.
8. Ice Level Control Board.
The ice level control board manages the ice production in the refrigerator.
If your refrigerator’s ice maker isn’t working, one of the possible causes could be a faulty ice level control board. This part is responsible for managing the ice production in the fridge, so if it’s not working properly, it can cause the ice maker to stop working.
Why does it fail?
Over time, the ice level control board can become damaged or worn out, which can cause it to fail.
How to fix it?
If you’re experiencing problems with your ice maker, it’s a good idea to check the ice level control board first. To do this, you’ll need to access the back of the fridge.
Once you’re there, locate the board and remove it. Inspect it for any signs of damage or corrosion. If you see any, then it’s likely that the board needs to be replaced.
If the ice level control board looks to be in good condition, then you’ll need to test it to see if it’s working properly. To do this, you’ll need a multimeter.
Once you have one, disconnect the power to the fridge and remove the board. Test it for continuity using the multimeter. If there is no continuity, then the board needs to be replaced.
How can I prevent it from happening again?
To prevent the ice level control board from failing, you should regularly clean and inspect it. If you see any signs of damage or wear, then you should replace the board.
Additionally, you should keep an eye on the ice maker itself and make sure that it’s working properly. If you notice any problems, then you should have the ice maker repaired or replaced.
9. Icemaker Mold Thermostat.
The icemaker mold thermostat is a part of the ice maker that helps to regulate the temperature of the ice mold. This part can fail over time and cause the ice maker to stop working.
If you notice that your ice maker is not making ice, or if it seems to be taking longer than usual to make ice, you may need to replace the icemaker mold thermostat. This is a relatively easy repair that you can do yourself.
Why does it fail?
The icemaker mold thermostat can fail for a variety of reasons. Over time, the part can become worn out from repeated use.
Additionally, the part can become damaged from exposure to high temperatures or from being dropped. If the icemaker mold thermostat is not working properly, it will need to be replaced.
How to fix it?
To replace the icemaker mold thermostat, you will need a Phillips screwdriver and a new icemaker mold thermostat.
First, locate the screw that holds the cover of the ice maker in place. Remove this screw and the cover.
Then, locate the two screws that hold the icemaker mold thermostat in place. Remove these screws and carefully pull out the old icemaker mold thermostat.
Next, take the new icemaker mold thermostat and insert it into the slot where the old one was located. Make sure that it is properly seated and then replace the two screws. Finally, replace the cover of the ice maker and screw it back into place.
How can I prevent it from happening again?
There are a few things that you can do to prevent the icemaker mold thermostat from failing again in the future.
First, make sure to clean the ice maker regularly. This will help to remove any dirt or debris that could build up and cause problems.
Additionally, be careful not to drop or damage the icemaker mold thermostat. If you do need to replace the part, make sure to get a high-quality replacement that is designed to last.
10. Icemaker Switch.
The icemaker switch is located in the control panel of your refrigerator. If your ice maker is not working, make sure that this switch is turned on.
Why does it fail?
The icemaker switch can fail because it is turned off, or because it is defective.
How to fix it?
If the icemaker switch is turned off, turn it on and see if the ice maker starts working again. If the switch is defective, you will need to replace it.
To replace the icemaker switch, you will need to remove the control panel from your refrigerator. Once you have removed the control panel, you will be able to access the switch.
Remove the old switch and install the new one in its place. Reconnect any wires that were disconnected and then replace the control panel. Test the ice maker to make sure it is working properly.
How can I prevent it from happening again?
There is not much you can do to prevent the icemaker switch from failing. However, you can check it periodically to make sure it is turned on. You may also want to consider replacing the switch with a higher quality one.
11. Water Filter.
A clogged or dirty filter can restrict the flow of water, which can lead to problems with the ice maker.
If you think the water filter might be the problem, check to see if it needs to be replaced and then try running the ice maker again. If that doesn’t solve the problem, you may need to call a repair person.
How can I prevent it from happening again?
Water filters should be replaced every six months or so to keep your refrigerator running smoothly. If you’re not sure how to replace the filter, consult your owner’s manual or contact Whirlpool customer service.
Related:
- Whirlpool Refrigerator Water Dispenser Not Working: How to Fix It
- 10 Reasons For Whirlpool Refrigerator Not Cooling and {How To Fix}
- How To Level A Whirlpool Refrigerator (6 Steps)
How do you reset a Whirlpool ice maker?
If your Whirlpool ice maker isn’t working properly, you may need to reset it. To do this, first unplug the ice maker from the power outlet. Then, remove the ice bin from the freezer and make sure that there is no ice blocking the fill tube or auger.
If there is, clear it away. Next, locate the reset button on the ice maker. It is usually located behind the control panel. Press and hold the reset button for about five seconds.
After that, replug the ice maker into the power outlet and wait for it to cycle through. Finally, replace the ice bin in the freezer and you’re all set!
Whirlpool refrigerator ice maker not working after filter change?
This is a common problem, and there are a few possible causes. The most likely cause is that the water line to the ice maker has become frozen. This can happen if the fridge is not properly cooled, or if there’s a leak in the water line.
Another possibility is that the ice maker itself is defective. If you’ve recently changed the filter, it’s possible that the new filter is not compatible with the ice maker. Finally, if the fridge is not level, this can also cause the ice maker to stop working.
If your ice maker has stopped working, first check to see if the water line is frozen. If it is, thaw it out with a hair dryer or a heat lamp.
If the water line is not frozen, then check to see if the ice maker itself is defective. You can do this by unplugging the fridge and then plugging it back in. If the ice maker still doesn’t work, then you’ll need to replace it.
If you’ve recently changed the filter, it’s possible that the new filter is not compatible with the ice maker. In this case, you’ll need to replace the filter with one that is compatible.
Finally, if the fridge is not level, this can also cause the ice maker to stop working. To fix this, simply adjust the legs of the fridge until it is level.
Whirlpool refrigerator ice maker not working after power outage?
There are several possible causes, but there are also a few solutions. Check out this blog post for more information.
One possible cause of your Whirlpool refrigerator ice maker not working after a power outage is that the ice maker was turned off during the power outage. This is a safety feature that prevents the ice maker from turning on and off unpredictably, which could damage the ice maker. To check if this is the problem, simply turn the ice maker on and see if it starts working again.
Another possible cause of your Whirlpool refrigerator ice maker not working after a power outage is that the power outage caused a surge that damaged the ice maker. If this is the case, you’ll need to replace the ice maker.
Fortunately, there are a few solutions that you can try if your Whirlpool refrigerator ice maker is not working after a power outage. First, you can try resetting the ice maker by unplugging it for 30 seconds and then plugging it back in. This will often reset the ice maker and get it working again.
If resetting the ice maker doesn’t work, you can try manually filling the ice maker with water. Simply pour a pitcher of water into the ice maker until it’s full and then wait for the ice to be made. This may take a few hours, but it will often get your ice maker working again.
Finally, if all else fails, you can always contact Whirlpool customer service for assistance. They may be able to help you troubleshoot the problem or even send someone out to repair the ice maker.
Whirlpool side by side refrigerator ice maker not working?
Here are some possible causes and solutions.
One reason your Whirlpool side by side refrigerator ice maker might not be working is because the water supply line is frozen. To fix this, simply thaw out the line with a hair dryer or by running warm water over it.
Another potential issue could be that the ice maker itself is frozen. If this is the case, unplug the refrigerator and let the ice maker thaw out for a few hours before plugging it back in and trying again.
If neither of these solutions work, then you may need to replace the water filter. A clogged water filter can prevent water from flowing properly through the ice maker, causing it to stop working. Simply replacing the water filter should fix the issue.
Whirlpool gold refrigerator ice maker not working?
If your Whirlpool gold refrigerator ice maker is not working, there are several potential causes. First, make sure that the power to the refrigerator is turned on and that the ice maker is turned on. There is usually a switch on the back of the refrigerator near the ice maker that must be in the “on” position. If this switch is turned off, the ice maker will not work.
Next, check to see if there is water available to the ice maker. There is a small water line that runs from the refrigerator to a water source. If this water line is kinked or frozen, it could be preventing water from reaching the ice maker. Try running some hot water through the line to thaw any ice that might be blocking it.
If there is water available to the ice maker and it still isn’t working, the next step is to check the ice maker’s fill tube. This tube brings water from the water line into the ice maker itself. If this tube is frozen, it will prevent water from entering the ice maker. Again, try running some hot water through the tube to thaw it out.
If the fill tube is not frozen and there is still no water entering the ice maker, the problem could be with the ice maker’s shut-off arm. This arm prevents water from entering the ice maker when it is full of ice. If the arm is stuck in the “up” position, it will prevent water from entering. Try moving the arm down manually to see if that solves the problem.
Finally, if none of these solutions work, you may need to call a technician to come and take a look at your ice maker. There could be a more serious problem that needs to be addressed.
Whirlpool french door refrigerator ice maker not working?
Here are some potential causes and solutions.
There are a few potential reasons why your Whirlpool french door refrigerator’s ice maker might not be working. One possibility is that the ice maker’s water supply line is frozen. If this is the case, you’ll need to thaw out the line before the ice maker will start working again.
Another potential issue could be that the ice maker’s bail arm is not in the correct position. The bail arm is the arm that controls whether or not the ice maker is turned on or off. If it’s in the “off” position, then the ice maker won’t work. Be sure to check and see if the bail arm is in the correct position and that it’s not accidentally been turned to the “off” position.
If neither of those solutions fix the problem, then you may need to replace the ice maker itself. Fortunately, Whirlpool french door refrigerator ice makers are relatively easy to replace and you should be able to find a replacement ice maker at most major home improvement stores.
Whirlpool bottom freezer refrigerator ice maker not working?
The most common cause of a Whirlpool bottom freezer refrigerator ice maker not working is because the ice maker is turned off. Check to see if the switch is in the “on” position. If it is, then flip it to the “off” position and wait 24 hours.
If the ice maker still does not work, then the next most common cause is a clogged water line. Check to see if the water line is kinked or frozen. If it is, then thaw it out and see if that fixes the problem. If the problem persists, then call a qualified technician to come take a look at your refrigerator.
Another common cause of a Whirlpool bottom freezer refrigerator ice maker not working is because the freezer temperature is set too high. The ideal freezer temperature is between 0 degrees Fahrenheit and -15 degrees Fahrenheit.
If the freezer temperature is set any higher than that, then it can cause the ice maker to stop working. So, if you suspect that the freezer temperature is too high, then open up the freezer door and check the thermostat. Adjust it accordingly and wait 24 hours to see if that fixes the problem.
Whirlpool top freezer refrigerator ice maker not working?
Here are some potential causes and solutions:
-Check if the ice maker is turned on. The switch is usually located in the control panel near the top of the refrigerator door.
-If the ice maker is on, check if there is water running to the ice maker. Check for a kinked or frozen water line.
-If there is water running to the ice maker, check if the ice maker shutoff arm is in the correct position. The shutoff arm controls the flow of water to the ice maker.
-If the shutoff arm is in the correct position, check if the ice mold is filled with water. If not, add water to the mold and wait 24 hours for the ice maker to produce ice.
-If the mold is filled with water, check if the ice maker is producing ice. If not, there may be a problem with the ice maker itself and you will need to call a repairman.
Whirlpool gold refrigerator ice maker not working and red light blinking?
There are a few things that could be causing this. Let’s take a look at some of the most common causes and solutions.
One of the most common reasons why your Whirlpool gold refrigerator ice maker not working is because there’s something wrong with the water line. This is usually caused by a kink in the line or a blockage. To fix this, you’ll need to locate the water line and clear any obstructions.
Another common reason why your ice maker isn’t working is because the freezer temperature is set too low. The ideal freezer temperature for an ice maker is between 0°F and -20°F. If your freezer temperature is set lower than this, it can cause the ice maker to stop working. To fix this, you’ll need to adjust the freezer temperature.
If your Whirlpool gold refrigerator ice maker not working and red light blinking, it could also be because of a faulty ice maker module. This is a more serious problem that will require you to replace the entire module.
Conclusion
If your Whirlpool refrigerator ice maker is not working, there are a few things you can do to troubleshoot it. First, check the power supply and make sure the ice maker is turned on. Next, clean the ice maker and ensure that there is no blockage preventing the ice from being made. Finally, if all else fails, you may need to replace the ice maker. With these simple tips, you should be able to get your Whirlpool refrigerator ice maker working in no time!
