Whirlpool Refrigerator Water Dispenser Not Working: How to Fix It

Last Updated on August 20, 2022 by Kimberly Crawford

If your Whirlpool refrigerator water dispenser is not working, don’t worry! You can fix it yourself. In this blog post, we will walk you through the steps to take to get your water dispenser up and running again. We will also provide some troubleshooting tips in case the problem persists.

Reasons Why Whirlpool Refrigerator Water Dispenser Not Working

1. Water Tube in Door.

About this part: The water tube in the door is a common problem. If the refrigerator is not used for a long time, the water in the tube can freeze and block the flow of water. The most common cause of this problem is a clogged filter.

Why does it fail?

There are several reasons why your water tube might fail. The most common reason is a clogged filter. If the filter is not changed regularly, it can become clogged with sediment and dirt. This will prevent the water from flowing through the tube and into the dispenser.

Another common cause of this problem is a frozen water line. If the refrigerator is not used for a long time, the water in the tube can freeze and block the flow of water.

How to fix it?

If your water tube is clogged, you will need to replace the filter. If the problem is a frozen water line, you will need to thaw the pipe with warm water. Once the pipe is thawed, you should be able to dispense water from the refrigerator.

How can I prevent it from happening again?

To prevent this problem from happening again, you should change the filter regularly and make sure that the refrigerator is turned on and off properly. You should also clean the water tube with a brush or other cleaning tool to remove any sediment that might be blocking the flow of water.

2. Water Inlet Valve.

If your water inlet valve is defective, it may not be allowing enough water into the refrigerator. As a result, the water dispenser will not work.

To test the water inlet valve, simply unplug the refrigerator and disconnect the water line from the valve.

Then, apply pressure to the line with your thumb and see if water flows freely through the valve. If it does not, then you will need to replace the water inlet valve.

Why does it fail?

The water inlet valve can fail for a number of reasons. The most common reason is simply because it is worn out from years of use.

Another possible reason is that the valve is not getting enough power. If you have checked the power supply and it seems to be fine, then the problem may be with the water inlet valve itself.

What are the symptoms?

If the water inlet valve is not working properly, you may notice that the water dispenser is not working as well. Additionally, you may see water leaking from the valve or hear a hissing noise coming from the valve.

How do I fix it?

The best way to fix a defective water inlet valve is to simply replace it. You can find replacement valves at most hardware stores or online. Be sure to get the right valve for your model of refrigerator.

How can I prevent it from happening again?

You can help prevent the water inlet valve from failing by regularly cleaning the filter. Additionally, be sure to keep an eye on the power supply to the valve and make sure it is not loose.

Finally, if you notice any leaks or strange noises coming from the valve, be sure to have it checked out as soon as possible.

3. Low Water Pressure.

One of the first things to check if your Whirlpool refrigerator water dispenser is not working is the water pressure. If the pressure is too low, it can cause problems with the dispenser.

The recommended water pressure for a Whirlpool refrigerator is between 30 and 120 psi. To check the water pressure, you will need a water pressure gauge. You can usually find these at hardware stores or home improvement stores.

Why does it fail?

There are a few reasons why your water pressure might be too low. It could be because of a problem with the main water line, a clogged filter, or a leak in the system.

If you have ruled out these other possibilities, then it is likely that the problem is with the pressure regulator. This is a device that controls how much water pressure is allowed into the system. It is located either on the main water line or on the back of the refrigerator.

If your water pressure is too low, you will need to adjust the pressure regulator. This can be done by turning the knob clockwise or counterclockwise.

If you are not sure how to do this, you can consult the owner’s manual for your refrigerator. Once you have adjusted the pressure regulator, you should see an improvement in the water dispenser. If not, then you may need to replace it.

Another possible cause of low water pressure is a clogged filter. The filter is located in the back of the refrigerator and helps to remove impurities from the water.

Over time, the filter can become clogged with dirt and debris. This can cause the water pressure to drop. To clean the filter, you will need to remove it and soak it in a solution of vinegar and water. After soaking for about 30 minutes, you should rinse it off and put it back in place.

How can I prevent it from happening again?

There are a few things you can do to prevent low water pressure in your refrigerator. Make sure that the main water line is turned on all the way. Check the pressure regulator regularly to make sure it is working properly. And be sure to change the filter every six months.

4. Dispenser Control Board.

The dispenser control board governs the water dispenser system.

When your Whirlpool refrigerator’s water dispenser suddenly stops working, there are a few possible causes. One of the most common is a problem with the dispenser control board. This part controls the water dispensing system, and if it malfunctions, the water dispenser will not work.

Why does it fail?

There are a few reasons why the dispenser control board might fail. One is simply age and wear and tear; over time, the board can become damaged and stop working properly. Another possibility is that the board has become wet or damp, which can cause it to short out.

If you suspect that the dispenser control board is the problem, you’ll need to replace it. This is a fairly simple repair that you can do yourself; just be sure to unplug your fridge before beginning any work on it.

To replace the dispenser control board:

First, locate the old board and unplug it. Then, remove the screws that hold it in place. Next, install the new board and screw it into place. Finally, plug your fridge back in and test the water dispenser to make sure it’s working properly.

How can I prevent it from happening again?

There are a few things you can do to prevent the dispenser control board from failing again.

First, make sure that your fridge is always properly plugged in and that the electrical outlet is working properly.

Secondly, avoid getting any water or moisture on the board itself. If it does become wet, dry it off immediately.

5. Dispenser Switch.

The dispenser switch is a momentary contact switch located in the control panel. When you press the lever to dispense water, the switch is engaged and sends power to the dispenser. If there is no power going to the dispenser, it will not work.

Why does it fail?

The dispenser switch can fail either mechanically or electrically. A failure is typically mechanical if the switch does not click when you press it, or if the lever feels loose.

An electrical failure is usually indicated by a clicking sound coming from the control panel when you press the lever.

What are the symptoms of this part failing?

If the dispenser switch fails, the water dispenser will not work.

How do you fix it?

If the problem is a mechanical failure, you can try to repair the switch yourself. However, if the problem is an electrical failure, you will need to replace the switch.

How can I prevent it from happening again?

You can prevent the dispenser switch from failing by regularly cleaning the switch and the control panel. You should also make sure that the lever is not loose and that there is no build-up of dirt or debris around the switch.

6. Door Switch.

The door switch signals the dispenser to turn on when the refrigerator door is open. If this switch is defective, it won’t signal the dispenser to turn on.

Why does it fail?

Over time, the door switch can become worn out or damaged.

What are the symptoms?

The water dispenser won’t turn on when you press the lever.

How do you fix it?

To check if your door switch is working properly, open and close your fridge door while watching the water dispenser.

If the dispenser doesn’t activate, then your door switch may be defective. You can test the door switch with a multimeter to see if it’s getting power. If not, then you will need to replace it.

How can I prevent it from happening again?

You can help prevent this issue by regularly cleaning your fridge door gasket. A dirty or damaged gasket can cause the door switch to fail.

7. Water Filter.

If your Whirlpool refrigerator water dispenser is not working, one of the first things you should check is the water filter. Clogged filters are a common cause of water dispenser problems. If your filter is clogged, it will need to be replaced.

Why does water filter fail?

There are a few reasons why your water filter may fail. The most common reason is that the filter gets clogged with dirt and debris.

If you don’t replace the filter regularly, it can become clogged and cause your water dispenser to stop working.

Another reason why filters fail is because they are not compatible with your refrigerator. Make sure you buy a filter that is specifically designed for your model of refrigerator.

How to fix it?

To check if your filter is clogged:

-Remove the filter from the fridge and inspect it for dirt or debris.

-If the filter is dirty, replace it with a new one.

You can find replacement filters at most home improvement stores or online. Be sure to purchase a filter that is compatible with your model of refrigerator.

Once you have replaced the filter, flush the water system by running water through the dispenser for several minutes. This will remove any air from the lines and get the water flowing again.

How can I prevent it from happening again?

To prevent your water filter from becoming clogged, replace it every six months or as often as the manufacturer recommends.

You should also clean the area around the water dispenser on a regular basis to remove any dirt or debris that could clog the filter.

Whirlpool refrigerator water dispenser very slow?

If your Whirlpool refrigerator water dispenser is very slow, there are several potential causes. First, make sure that the water line to the fridge is fully open and not kinked or frozen. Second, check the water filter and replace it if it’s clogged. Finally, clean the dispenser itself with a vinegar and water solution to remove any built-up sediment.

If you’ve tried all of these solutions and the water dispenser is still very slow, then it’s likely a problem with the fridge itself and you should call a repair person.

Whirlpool refrigerator water dispenser not working after replacing filter?

whirlpool refrigerator water dispenser not working after replacing filter

Here are some possible causes and solutions to help you get your water dispenser working again.

1. Air in the Water Line

One possible cause of your Whirlpool refrigerator water dispenser not working after replacing the filter could be air in the water line. When you replace the filter, air can get trapped in the water line and prevent water from flowing to the dispenser.

Solution:

To get rid of the air in the water line, bleed the air out of the line. To do this, locate the bleeder valve on the water line (usually near where the water line connects to the back of the refrigerator).

Place a bowl or bucket under the bleeder valve and open the valve to release the air. Once water starts flowing from the valve, close it and your water dispenser should start working again.

2. The Water Filter Is Not Seated Properly

Another possible reason why your Whirlpool refrigerator water dispenser not working after replacing the filter is that the new filter is not seated properly. If the filter is not seated correctly, it can prevent water from flowing through it and to the dispenser.

Solution:

To fix this, remove the old filter and reinstall the new one, making sure that it is inserted correctly and firmly in place. Once the new filter is installed properly, the water dispenser should start working again.

3. The Water Supply Valve Is Turned Off

If the water supply valve to your refrigerator is turned off, this can obviously prevent water from flowing to the dispenser (even if the filter has been replaced).

So, if your Whirlpool refrigerator water dispenser not working after replacing the filter, check to make sure that the water supply valve is turned on.

Solution:

To turn on the water supply valve, locate it (usually under the sink) and turn it clockwise until it is fully open. Once the valve is open, try using the water dispenser again and see if it works.

4. The Dispenser Solenoid Is Defective

The dispenser solenoid is a small coil of wire that opens and closes the water valve when you press the dispenser lever. If this solenoid is defective, it can prevent water from flowing to the dispenser, even if the water supply valve is turned on and the filter is new.

Solution:

If you suspect that the dispenser solenoid is defective, you will need to replace it. This is a relatively easy repair that you can do yourself with a few tools. Or, you can call a refrigerator repair technician to do it for you.

5. The Dispenser Switch Is Defective

The dispenser switch is what tells the dispenser solenoid to open and close the water valve. If this switch is defective, it can prevent water from flowing to the dispenser.

Solution:

If you suspect that the dispenser switch is defective, you will need to replace it. This is a relatively easy repair that you can do yourself with a few tools. Or, you can call a refrigerator repair technician to do it for you.

6. The Water Inlet Valve Is Defective

The water inlet valve is what supplies water to the refrigerator. If this valve is defective, it can prevent water from flowing to the dispenser (even if the filter has been replaced).

Solution:

If you suspect that the water inlet valve is defective, you will need to replace it. This is a relatively easy repair that you can do yourself with a few tools. Or, you can call a refrigerator repair technician to do it for you.

7. Something Is Blocking the Water Dispenser Tube

If something is blocking the water dispenser tube (such as a piece of ice), this can obviously prevent water from flowing to the dispenser. So, if your Whirlpool refrigerator water dispenser not working after replacing the filter, check to see if there is anything blocking the water tube.

Solution:

To fix this, simply locate the blockage and remove it. Once the blockage has been removed, try using the water dispenser again and see if it works.

8. The Dispenser Motor Is Defective

The dispenser motor is what powers the dispense function of the water dispenser. If this motor is defective, it can prevent water from flowing to the dispenser.

Solution:

If you suspect that the dispenser motor is defective, you will need to replace it. This is a relatively easy repair that you can do yourself with a few tools. Or, you can call a refrigerator repair technician to do it for you.

9. The Dispenser Housing Is Leaking Water

If the dispenser housing is leaking water, this can obviously prevent water from flowing to the dispenser (even if the filter has been replaced). So, if your Whirlpool refrigerator water dispenser not working after replacing the filter, check to see if there is any water leaking from the dispenser housing.

Solution:

If you find that the dispenser housing is indeed leaking water, you will need to replace it. This is a relatively easy repair that you can do yourself with a few tools. Or, you can call a refrigerator repair technician to do it for you.

10. The Dispenser Housing Is Cracked or Broken

If the dispenser housing is cracked or broken, this can obviously prevent water from flowing to the dispenser (even if the filter has been replaced). So, if your Whirlpool refrigerator water dispenser not working after replacing the filter, check to see if there is any damage to the dispenser housing.

Solution:

If you find that the dispenser housing is indeed cracked or broken, you will need to replace it. This is a relatively easy repair that you can do yourself with a few tools. Or, you can call a refrigerator repair technician to do it for you.

How do I reset my Whirlpool refrigerator after changing the water filter?

To reset your Whirlpool refrigerator after changing the water filter, simply press and hold the “Filter Reset” button for three seconds. This will clear the “change filter” indicator light and reset the filter life indicator. For more detailed instructions, please consult your Owner’s Manual.

Whirlpool refrigerator water dispenser not working but ice maker is?

whirlpool refrigerator water dispenser not working but ice maker is

This is a common issue. Let’s take a look at some possible causes and solutions.

One possibility is that the water line that supplies the water dispenser is frozen. This can happen if the ambient temperature drops suddenly or if the refrigerator has been recently installed in a very cold location. To fix this, simply locate the water line and thaw it out with a hair dryer.

Another possibility is that the water filter needs to be replaced. The water filter should be replaced every six months, so if it’s been longer than that, it’s probably time for a new one. Simply remove the old filter and install a new one following the instructions in your owner’s manual.

If neither of these solutions solves the problem, then it’s likely that there is a problem with the water dispenser itself. In this case, you’ll need to contact a qualified refrigerator repair technician for further diagnosis and assistance.

Whirlpool refrigerator water dispenser works intermittently?

If your Whirlpool refrigerator water dispenser is working intermittently, there are a few possible causes and solutions. First, check to make sure that the water line is connected to the fridge properly.

If it’s not, tighten the connection or replace the water line. Next, clean the dispenser nozzle with a toothbrush or other small brush. If the dispenser is still not working properly, you may need to replace the water filter. Finally, if none of these solutions work, you may need to call a repairman.

Whirlpool refrigerator water dispenser not working after power outage?

whirlpool refrigerator water dispenser not working after power outage

This can be caused by a number of factors. Here are some solutions to try.

-First, check to see if the water line is still connected and there is water flowing to the refrigerator. If not, reconnect the water line and turn on the water supply.

-Next, check to see if the power outlet is working by plugging in another appliance. If the power outlet is not working, reset the circuit breaker or replace the fuse.

-If the power is on and there is water flowing to the refrigerator, but the water dispenser still does not work, try pressing and holding the reset button for 30 seconds. This will sometimes clear any air bubbles that may be in the line.

-If the water dispenser still does not work, check to see if there is ice build up around the water line. If so, thaw the ice with a hair dryer and try again.

How do I reset my Whirlpool fridge after a power outage?

If your Whirlpool refrigerator experiences a power outage, the first thing you need to do is check the breaker or fuse box. If the power is out to your home, resetting your fridge will not be possible.

Once you have confirmed that there is power to your home, locate the control panel on your fridge. On most models, the control panel is located on the inside wall of the fridge, near the top.

Locate the power button on the control panel and press it to turn your fridge back on. If your model does not have a power button, simply turn the temperature knob to the “off” position and then back to the desired setting. Once your fridge is turned back on, it should reset itself and begin cooling again.

If your Whirlpool refrigerator does not have a power button, you may need to reset it manually. To do this, locate the circuit breaker or fuse box for your fridge and turn off the power. Leave the power off for at least 30 seconds before turning it back on. Once the power is back on, your fridge should reset itself and begin cooling again.

New Whirlpool refrigerator water dispenser not working?

If you recently installed a new Whirlpool refrigerator with a water dispenser and it’s not working, there are several possible causes. In this article, we’ll troubleshoot the most common reasons why your new Whirlpool refrigerator’s water dispenser isn’t working and what you can do to fix it.

First, make sure that the water line to the refrigerator is turned on. The water line is usually located behind the fridge. If the water line is turned off, turn it on and wait 24 hours for the water to start flowing through the dispenser.

If the water line is turned on and you’re still not getting any water from the dispenser, check to see if the water filter needs to be replaced. A clogged or dirty water filter will prevent water from flowing through the dispenser.

If the water filter is clean and you’re still not getting any water, there may be an issue with the ice maker. If the ice maker isn’t working, it could be preventing water from flowing to the dispenser.

Whirlpool french door refrigerator water dispenser not working?

whirlpool french door refrigerator water dispenser not working

Don’t worry, we’ll help you figure out the root of the problem and how to fix it.

There are a few reasons why your water dispenser might not be working. The first thing you should check is the water line that runs from the fridge to the water source. If this line is kinked or frozen, it could be the reason why water isn’t flowing into the fridge.

If the water line is clear, the next thing to check is the water filter. If the filter is clogged, it will need to be replaced. You can find your model’s specific replacement instructions in your owner’s manual.

Once you’ve replaced the filter, flush the water system by dispensing water until it runs clear. If you’re still having trouble, give us a call and we’ll be happy to help.

How do you reset the water dispenser on a Whirlpool refrigerator?

If your Whirlpool refrigerator has a water dispenser that needs to be reset, you can follow these simple steps.

First, turn off the power to the dispenser at the circuit breaker or fuse box.

Next, disconnect the water line from the inlet valve on the back of the fridge. Once the water line is disconnected, flush the line by holding a cup under the dispenser and running the water until it is clear.

Finally, reconnect the water line and turn on the power to the dispenser. Your Whirlpool refrigerator’s water dispenser should now be reset and ready to use.

How do I know if my water inlet valve is bad on my Whirlpool refrigerator?

If your refrigerator is not dispensing water or producing ice, it could be a sign that your water inlet valve is bad.

Other signs that your water inlet valve may be failing include water leaking from the valve or a slow flow of water into the refrigerator. If you suspect that your water inlet valve is failing, contact a qualified refrigerator repair person for diagnosis and repair.

How do you calibrate a Whirlpool water dispenser?

Whirlpool water dispensers come with a built-in calibration feature that helps ensure accuracy and consistency when measuring out water. To calibrate your Whirlpool water dispenser, follow these simple steps:

First, fill a container with one gallon of cold water. Next, place the container under the dispense spout and press the button to dispense water. The water dispenser should dispense one gallon of water within 30 seconds.

If the water dispenser does not dispense one gallon of water within 30 seconds, it needs to be calibrated. To calibrate the water dispenser, press and hold the button for three seconds. The built-in calibration feature will automatically adjust the water flow rate.

Once the calibration is complete, your Whirlpool water dispenser will be accurate and consistent when measuring out water. This is a quick and easy way to ensure that you always have the perfect amount of water for your needs. Whether you’re making a pot of coffee or just need a quick drink of water, your Whirlpool water dispenser will be there to help.

Where is the water filter reset button on Whirlpool refrigerator?

The water filter reset button on a Whirlpool refrigerator is usually located in the back, near the top. If you cannot find it there, check the manual that came with your fridge.

The water filter reset button is used to reset the indicator light that tells you when it is time to replace the water filter. Pressing this button will usually cause the light to go off.

Related:

Conclusion

So, there you have it. These are the most common issues that can cause your Whirlpool refrigerator’s water dispenser to stop working. By troubleshooting the problem and following the steps outlined in this article, you should be able to get your water dispenser up and running again in no time. Thanks for reading!